Countax A20/50 Скачать руководство пользователя страница 8

Page 8

Page 21

Engine - General Maintenance

Rear Discharge Deck

fig 1

Specified Belts and Blades

Engine/Deck Belt - B56 Dayco Super II - Pt No. 22940100 (IBS)

Engine/Deck Belt - B57 Dayco Super II - Pt No. 22871200 (MULCH)

Deck Internal Drive Belt (Mulcher) - BB112 Pt No. 228000900

(Rear Discharge) - Dayco Super II BB155 Pt No.  22950200

Mulcher Blades x3 Pt No. - 216938100

IBS RH Blade Pt No. 169381300

IBS LH Blade Pt No. 169381400

IBS Front Blade Pt No. 1692000

PGC Drive Belt Super II A49 - Pt No. 228001200 

PTO Drive Belt -  Dayco Super II A92 - Pt No. 22950100

Transmission Drive Belts - A92 Dayco Super II - Pt No. 22950100

N.B. Only use specified Belts and Blades - Never accept a substitute!

Routing for IBS internal deck drive belt

VANGU

ARD

AIR INTAKE/COOLING SYSTEM

The cooling fan also supplies the air to the carburettor. If the
engine will not start or if it is stalling or overheating:

CHECK THE COOLING SYSTEM AND THE AIR

FILTERS

1. Ensure that vents on either side of the bonnet are not 

blocked (fig 2).

2. Check that debris is not caught in the Cooling Fan Cover – 

clean with a stiff brush (fig 1).

3. Remove the air-filter cartridges and check that debris is not 

gathered on Pre-Cleaner (fig 3).

After all three checks you must consider whether the air filter
cartridges should be replaced.

PRE-CLEANER BRIGGS & STRATTON PART 271271,
CARTRIDGE PART 394018

HYDROSTATIC OIL RESERVOIR

At the back of your Tractor, in the PTO compartment, you will
find the hydrostatic oil reservoir (fig 4). The oil in this is the
transmission medium for the drive

and the level needs to be

checked regularly.

To check, turn the cap anti-clockwise and ensure that the oil is
up to the correct level. If it needs topping up refill with good
quality SAE 10W40 engine oil to the mark as shown in fig 4.

fig 1

fig 2

fig 3

fig 4

AIR VENTS

Cooling

Fan Cover

Clean out

Chaff and Dirt

Cover

Knob

Plate

Pre-cleaner

Cartridge

Содержание A20/50















Отзывы: