manualshive.com logo in svg

Cotic droplink Flare Gen2, Руководство пользователя

Поделиться
Скачать
Cotic droplink Flare Gen2 Скачать руководство пользователя страница 11

                     Pivot                                             Torque                                        Head Sizes

 

              Main Pivot Axle                                          17Nm                              8mm allen key/17mm spanner 

       Main Pivot Pinch Clamps                                    6Nm                                           4mm allen key  

         Droplink Seat Tube End                                     N/A*                               8mm allen key/6mm allen key 

         Seatstay/Droplink Pivot                                     7Nm                                    4mm allen key/T25 Torx 

         Droplink Pinch Clamps                                     7Nm                                           4mm allen key 

                Seatstay Pivot                                           11Nm                                          5mm allen key 

             Shock Mountings                                         7Nm                                        2 x 4mm allen key 

All the pivots and pinch clamps are designed to be done up with the following torque settings: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
*There is no specified torque for the 

drop

link

 Seat Tube Pivot Axle (15mm diameter). This is because for maximum 

bearing life, the pivot should be assembled loosely, with threadlock on the large screw and the 

drop

link

 pinch clamps 

undone. The 15mm axle should then be tightened until there is just enough preload to remove any slack in the pivot, 
but still allows free turning. Just like pre-loading a headset. Once at this point, tighten the 

drop

link

 pinch clamps to 

the recommended torque to hold the assembly together.  
 
This ensures safe operation of the frame. Failure to install the spacers and pivots correctly, or to tighten the bolts  
sufficiently will lead to premature frame failure. If you're at all unsure, get your Independent Mountain Bike Specialist 

to do the job for you.

 

Feel free to contact Cotic for answers to any specific questions or to return the frame to us for service. 
 
 

Other General Specifications

 

 
Seat Clamp (supplied)                   34.9mm 
Front Derailleur                            N/A – The frames are 1x drivetrain only                               
Bottom Bracket Shell                    BSA 73mm threaded 
Chainguide Mounting                   ISCG05 lower 2 tabs. Integrated  
                                                    Cotic / One Up Components top  
                                                    guide supplied with frame/bike

 

Cable/Hose Routing                      Down tube routed full outer for gears,  
                                                    internal dropper post and rear brake.  
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание droplink Flare Gen2

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды