Brake
6- Applying:
7- Releasing:
Front wheel swivel
lock
8- Applying:
9- Releasing:
Handle
10- Adjusting handle height:
11- Adjusting handle position:
Note:
The handle position can be reversed. This is useful if the chassis is used on
uneven terrain. As this may make the chassis harder to steer so Cosatto recommend
returning the handle to the normal position for use on a flat surface.
Note:
Prior to adjusting, raise the handle to its highest position 10 .
(a) Normal position
(b) Reversed position
(c) Closing position
Basket
12- Fitting:
Removing is a reversal of this procedure.
Chassis
13- Closing:
Note:
Prior to closing, please ensure that both front wheel swivel locks are released 9 .
Lower the handle height to its lowest position 10 and set in closing position 11 .
While pressing the primary release button (1), lift the secondary lever (2).
Lift the chassis off the floor to allow the front legs to fold inwards (3).
Carrycot
14- Preparation:
Remove mattress and liner from carrycot (1).
Unfold both frame bars until they lock into positions (2).
Refit the liner into the carrycot and secure (3).
Refit the mattress over the liner in the carrycot (4).
15-
Secure the hood fabric to the carrycot frame (1).
Fold out the carrycot mountings (2).
There are a set of “D” ring located at the base of the carrycot for the attachment of a
separate safety harness approved to BS EN 13210 should this be required (harness not
supplied). Push the ‘D’ rings through the slots in the liner (3).
Carrycot hood
16- Opening:
17- Closing:
Carrycot apron
18- Fitting:
Removing is a reversal of this procedure.
Carrycot
19- Fitting:
Note:
The carrycot can only be fitted rearward facing as shown in illustration.
20- Removing:
Note:
Before lifting the carrycot off the chassis. Ensure that the carry handle on the
hood is locked into position 16 .
Carrycot raincover
21- Fitting:
Removing is a reversal of this procedure.
22- Using access zip:
Seat unit
23- Preparation:
Open the seat unit (1).
Adjust the calf support to its highest position 41 (2).
Align and secure the calf support section to the seat unit (3).
Check the lock pin on both sides are locked into position.
Fasten the fabric fastener over the seat unit support bar (4).
24- Fitting:
Note:
The seat unit can be fitted forward or rearward facing.
25- Removing:
Содержание NITTY GRITTY ooba
