Cornell SGHNX-10011E Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 37

background image

7

SGHNX Series

REVISION # 0000

DATE: 03/07/2017

DRIVE CHAIN ADJUSTMENT

NOTE: Use correct type, size and proper length of roller chain.

1. Adjust the drive chain by tilting or move the operator so that there is about 1/4” of slack when the

chain is depressed.

Note: The set screw included in the operator may be used for adjustment. (See figure 1- S1 location for

1/2hp and 3/4hp), (See figure 2 - T1, T2, T3, T4 for 1hp and 1½hp).

2. Once the drive chain has been tightened and the base leg screws have been set, and then tighten the

operator screws.

S1

Drive Chain

Door Sprocket

Drive Sprocket

1/4"

S1

Drive Chain

Door Sprocket

Drive Sprocket

1/4"

(Figure 1 for 1/2hp and 3/4hp)

Drive Chain

Door Sprocket

Drive Sprocket

1/4"

T1

T2

Drive Chain

Door Sprocket

Drive Sprocket

1/4"

T3

T4

(Figure 2 for 1hp and

1½

hp)

«
...
6
7
8
9
10
...
»

Содержание SGHNX-10011E






































Отзывы:

Нет отзывов

Похожие инструкции для SGHNX-10011E

Бренд: Hamilton Beach Страницы: 20

Бренд: Hamilton Beach Страницы: 20

76375 - CleanCut Extra-Tall Can Opener

Бренд: Hamilton Beach Страницы: 10

Бренд: FAAC Страницы: 14

Бренд: BFT Страницы: 120

SeceuroGlide Classic

Бренд: SWS Страницы: 12

Бренд: Teckentrup Страницы: 76

Бренд: CAME Страницы: 80

Бренд: Accessmatic Страницы: 39

Бренд: CAME Страницы: 24

Бренд: CAME Страницы: 44

SECURITY+ 3265GCM 1HP

Бренд: Garaga Страницы: 72

Бренд: CAME Страницы: 16

Бренд: Continental Refrigerator Страницы: 4

Бренд: Imusa Страницы: 24

Бренд: Timotion Страницы: 12

Бренд: Toastmaster Страницы: 6

Бренд: Elite access systems Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды