Cornelius "I" Series 227 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 13

Cornelius

6

OWNER - OPERATOR

The installation is not complete until you are sure the owner-operator understands the cuber operation
and his or her responsibility of preventative maintenance.

Does the owner-operator know:

1. Location of electrical disconnect switch and water shut-off valves?

2. How to start and/or shut down the product, clean and sanitize it?

3. Bin full operation and reset operation of high pressure cutout (water-cooled and remote products

only)?

4. How to clean the condenser and fan blade?

5. Whom to call for product information and/or service?

CLEANING PROCEDURES

Approved ice machine cleaners by brand names:

S

Lime–A–Way

S

Calgon Nickel Safe (green color only)

NOTE:

All ice machine cleaners labeled safe for nickel ARE NOT the brand CALGON NICKEL

SAFE.

CAUTION: Ice machine cleaners are acidic-based chemicals. Before beginning any
cleaning of the cuber, the ice in the storage bin or dispenser must be removed.

WARNING: When using any chemical, rubber gloves and eye protection should be worn.

PREP – CLEANING

Use full-strength ice machine cleaner on a coarse-surface cloth material (such as terry cloth) and wipe
down the inside wall of the evaporator area, the water pan, the water curtain and evaporator plastic extru-
sions. If the water distributor tube has heavy scale build–up, remove and soak it in full-strength ice ma-
chine cleaner (or exchange the tube and clean the scaled tube at a later date).

CLEANING THE WATER SYSTEM & EVAPORATOR

1. Set the switch to CLEAN and allow the ice on the evaporator to release and melt away.

2. Remove all ice from the storage bin.

3. Remove the water curtains, pour 1/2 oz. of ice machine cleaner down the rear key-slot openings.

The cleaner will drain into the water pan.

4. Return the water curtains to their proper operating position.

5. Add 3 oz. for a single evaporator, or 5 oz. for a dual evaporator of “Calgon Nickel-Safe” or “Lime-A-

Away” ice machine cleaner directly into the water pan. Set switch to CLEAN, circulate for a maxi-
mum of 15 minutes

6. Depress and hold the dump switch to allow the cleaner to drain away.

«
...
6
7
8
9
10
...
»

Содержание "I" Series 227














Отзывы:

Нет отзывов