Cornelius

1

 GENERAL

FREIGHT DAMAGE CLAIMS PROCEDURE

The deliverer of your equipment (freight company, distributor or dealer) is responsible for loss or damage
of your shipment. All claims must be filed with the deliverer of your equipment. Please follow the steps
below to determine if your shipment is satisfactory or if a claim must be filed:

1. Check the number of products delivered against the number of products listed on the delivery re-

ceipt. Should the totals not match, have the driver note all errors on both copies and both you and
the driver sign and date said notation.

2. Inspect all cartons for visible damage. Open and inspect as required before the driver leaves and

have him or her note any damage on the receipts. All damaged claims must be inspected within 15
days of delivery. Notify your carrier immediately if concealed damage is found after delivery.

3. Should concealed damage be found when product is unpacked, retain the packing material and the

product and request an inspection from the deliverer.

4. All claims for loss or damage should be filed at once. Delays in filing will reduce the chance of

achieving a satisfactory resolution to the claim.

SPECIFICATIONS, ICE CUBER

The following table contains equipment specification information for the Ice Cubers.

Model

IACS227

IWCS227

IACS227E60

IWCS227E60

IACS227E50

IWCS227E50

UNIT

Volts

115

230

220

Phase

1

Hertz

60

50

No. Wires

2+Ground

MIN. CIRCUIT
Amps

20

15

MAX. FUSE SIZE

Amps

20

15

REFRIGERANT

Type

R404A

Weight (oz)

17

15

17

15

17

15

Weight (g)

482

425

482

425

482

425

COMPRESSOR

Volts

115

230

220

Phase

1

Hertz

60

50

LRA

51

24

26

RLA

11.5

5.7

5.3

CONDENSER FAN MOTOR

Volts

115

230

220

Phase

1

Hertz

60

50

Amps

1.7

NA

1.2

NA

0.75

NA

Watts

50

NA

60

NA

50

NA

WATER PUMP

Volts

115

230

220

Phase

1

Hertz

60

50

Amps

0.88

0.5

Watts

1/40

1/30

Important: 

All product supply voltage specifications are –5%/+10% for proper component operation.

Содержание "I" Series 227














Отзывы: