Coram Showers 1000 Door X Скачать руководство пользователя страница 6

Страница: 6 / 8

Inside

Outside

Select the vertical seal with the 9mm flipper (PN40260) and trim to 1785mm.

Push fit trimmed 'flipper seal' onto the back edge of the door.

Ensure the flipper seal 'flap' is on the outside of the door.

Select the magnetic seal (PN40332) and trim to 1785mm. Push fit 'magnetic seal' onto the closing edge of the doors (the same

side as door handle).

Note:

Ensure the magnetic seal is positioned as shown.

Note:

Wetting the glass with water will help fit the seals.

Important: Ensure that the coated side of the glass is on the inside of the door.
Attach the wheels to the door:

Adjuster wheels (PN60517) at the top and plunger wheels (PN60518) at the bottom.

Attach as shown and fix using the screw and screw cap (bottom 'plunger wheels' are shown as an example).

PN40260

Inside

face of

door

PN40332

Inside

face of

door

9mm

PN40260

Trim to

1785mm

IMPORTANT

Ensure that the coated
side of the glass is on
the inside of the door.

PN60518

Inside face

of door

Bottom 'plunger wheels' are shown as an example.

PN60517

PN60518

Trim to

1785mm

Inside

Outside

PN40332

Inside

Содержание 1000 Door X









Результаты поиска

Содержание 1000 Door X

Отзывы:

Похожие инструкции для 1000 Door X

Бренды по названию

Популярные бренды

Coram Showers 1000 Door X, Быстрый старт

Результаты поиска

Содержание 1000 Door X

Отзывы:

Похожие инструкции для 1000 Door X

Бренды по названию

Популярные бренды