3
Installation Instructions for the AUX Universal Edge Lit Exit
• For wall or ceiling mount, attach the canopy over the hole in the
center of the housing using the screws used to hold the hanger bar
brackets (See Figure 7).
• For end mount, remove the endcap on the desired end, and replace it
with the canopy and guide bracket (See Figure 8). Replace the cover
plate over the hole in the center of the housing.
4. Remove the screws securing the trim plate to the housing (See
Figure 1). Place the trim assembly and screws aside and save
them for later installation. It is not necessary to disconnect the
wire harness connecting the charger driver circuit board to the LED
board. Instead, the trim plate can be hung from the sliding plastic
installation hook (See Figure 2).
Secure the canopy to the junction box using the adapter plate and
screws provided (See Figure 7/8). The adapter plate is designed
to be connected to a NEMA standard 3.5” round, 4” round, 3.5”
octagon,4” octagon, or handy (single gang) box. However, it is
possible to connect the adapter plate to other electrical boxes with
some modification.
5. Connect power supply and ground in accordance with NEC and local
codes. Wire connections are as follows: Ground to Green Lead,
Neutral to White Lead, 277V line to Orange Lead (if used), 120V line
to Black Lead (if used). Cap unused Line Lead. (See Schematic)
6. Excess wire length can be held in place in the wire trap (See Figure
5).
7. If the fixture is to be wall mounted, first, loosen the set screw on the
back of the pivot housing. Then remove the locking clip by sliding
it to the end of the pivot housing (See Figure 5). Rotate the pivot
housing 90 degrees, and then replace the locking clip. Tighten the set screw.
8. Remove the trim assembly from the installation hook.
9. Replace the screws holding the trim assembly to the housing.
10. Lens is provided in a separate box. Apply chevrons and background as needed. Snap lens into place.
NOTE: If using the lens with the default transparent background (instead of the provided white or mirror
backgrounds) it must be installed only where there is adequate color contrast between the sign legend and the
interior wall finish behind the sign, to provide for sufficient visibility.
11. Turn on power to fixture. Remove EZ Key battery disconnect.
Activating Optional Features:
FLASHER:
If the consumer desires the exit sign to flash on and off when in emergency mode, remove the jumper
labeled FLASHER from the circuit board while unit is de-powered. See Schematic.
MAINTENANCE:
None required.
NOTE:
Servicing of any parts should be performed by qualified personnel. Only use replacement
parts
supplied by
Cooper Lighting Solutions
. Use of unauthorized parts may void the warranty
ADAPTER
PLATE
HANGER
BAR
ASSEMBLY
COVER
PLATE
HANGER BARS
ADJUSTED FOR 5/8"
THICK DRYWALL
PIVOT
HOUSING
LOCKING
CLIP
TRIM
ASSEMBLY
PLASTIC
INSTALLATION
HOOK
ADAPTER
PLATE
GUIDE
BRACKET
HOUSING
TRIM PLATE
FIGURE 1
HOUSING
FIGURE 3
FIGURE 6
HOUSING
FIGURE 2
FIGURE 7
HOUSING
CANOPY
HOUSING
COVER PLATE
CANOPY
FIGURE 8
FIGURE 4
FIGURE 5
WIRE IN WIRE TRAP
ADAPTER
PLATE
HANGER
BAR
ASSEMBLY
COVER
PLATE
HANGER BARS
ADJUSTED FOR 5/8"
THICK DRYWALL
PIVOT
HOUSING
LOCKING
CLIP
TRIM
ASSEMBLY
PLASTIC
INSTALLATION
HOOK
ADAPTER
PLATE
GUIDE
BRACKET
HOUSING
TRIM PLATE
FIGURE 1
HOUSING
FIGURE 3
FIGURE 6
HOUSING
FIGURE 2
FIGURE 7
HOUSING
CANOPY
HOUSING
COVER PLATE
CANOPY
FIGURE 8
FIGURE 4
FIGURE 5
WIRE IN WIRE TRAP