Cooper Lighting Solutions Lumark AP Скачать руководство пользователя страница 2

2

Cooper Lighting Solutions    

 IB514101EN 

    

 Installation instructions

Installation Instructions – LAS Area / Site

 

Selectable Lumen Switch

Tools Required:

 

• 

5mm Allen Wrench

• 

Torque Wrench 

• 

Small Flat Head screwdriver (provided)

ote: 

N

Ensure there is no power to the fixture prior to 

adjusting the selectable lumen switch.

ote: 

N

If for use with external controls system, follow 

instructions below but remove dimming leads from 

selectable lumen switch for use external to luminaire.

1.  Open the fixture door by loosening the three Allen head 

screws. (Figure 1.) No need to completely remove the 

Allen head screws, there is a rubber ring on each screw 

to hold it to the housing door.

Figure 1.   

Figure 2.   

Figure 3.   

Allen 

Head 

Screws

2.  Using the provided small flat head screwdriver, adjust 

the selectable lumen switch to the desired light level. 

Nominal lumens in table below. For specific value by 

optical distribution, refer to product specification sheet.

3.  Close and reinstall the door to the housing by 

tightening the three Allen head screws to 30 in-lbs. Be 

sure not to pinch any wires when closing the door.

Installation

Slipfitter Mounting Arm
Tools Required:

 

• 

#2 Phillips screwdriver

• 

4/5/6mm Allen wrenches

• 

Torque Wrench 

• 

M15/M17 Socket Wrench

• 

Drill (optional)

1.  Remove the cover plate on the slipfitter mounting arm 

via two Phillips head screws and set aside. (Figure 2.) 

No need to completely remove the four Phillips head 

screws, there is a rubber ring on each screw to hold it 

to the cover plate.

Phillips Screw

Phillips Screw

2.  Route wire leads from luminaire into the slipfitter and 

install slipfitter onto luminaire. Secure with two Allen 

screws. Tighten to 30 in-lbs. (Figure 3.)

ote: 

N

Be sure not to pinch wires between slipfitter and 

luminaire.

Allen 

Head 

Screws

Switch 

Position

LAS45

LAS100

Lumens

HID 

Equivalent

Lumens

HID 

Equivalent

0 (Factory 

pre-set)

20,000

450W

34,000

1,000W

1

18,400

400W

31,100

750W

2

16,800

250W

28.400

750W

3

14,500

250W

24,500

450W

4

13,400

250W

22,600

450W

5

12,000

150W

20,400

450W

6

11,500

150W

19,500

450W

7

10,700

100-150W

18,100

400W

8

4,900

70W

8,300

-

9

4,900

70W

8,300

-

Содержание Lumark AP














Отзывы: