background image

17

Mains lead replacement

Do not attempt to repair or replace the mains connecting cable yourself, consult a qualified
electrician.

The oven is supplied with a fitted plug which contains a
13A fuse. If you are simply replacing the fuse, you
must use a 13A fuse which has been approved by
ASTA to BS1362.

If the oven’s plug does not fit the socket or becomes
damaged, a new plug must be fitted. Replace the
original plug with the correct plug for your socket. If this
is a 3-pin (square pin) 13A (BS1363) plug, you must
make sure that it is fitted with an ASTA approved 13A
fuse. If another type of plug is used, it must be
protected by a 15A fuse, either in the plug or at the
distribution board.

The hob is also supplied with a fitted plug which
contains a 3A fuse. If replacing this fuse it must also be
approved by ASTA to BS1362

If the hob’s plug does not fit the socket, or is damaged,
the same rules apply to fittng a new plug as for the
oven, but with an ASTA approved 3A fuse.

1. Remove the existing fitted plug.

2. The wires in the mains lead supplied with this appliance are coloured in accordance with the following
code:

GREEN/YELLOW = EARTH (E)      BLUE = NEUTRAL (N)      BROWN = LIVE (L)

This product must be earthed

As the colours of the wires in the mains lead may not correspond with the colour markings identifying the
terminals in your new plug, proceed as follows.

The wire which is coloured GREEN or GREEN/YELLOW must be connected to the terminal which is
marked with the letter E or 

E

symbol or coloured GREEN or GREEN/YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the
letter N or coloured BLACK or BLUE.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or
coloured RED or BROWN.

3. Ensure that the connections are tight and that no loose strands are left out of the terminals.

IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.

GREEN/
YELLOW
(EARTH)

BLUE 
(NEUTRAL)

BROWN
(LIVE)

FUSE

CABLE
CLAMP

Plug replacement

Figure 22 - plug wiring

Содержание CZ55524





















Отзывы: