CoolAutomation CoolMasterNet Скачать руководство пользователя страница 36

Страница: 36 / 47

ASCII I/F

CoolMasterNet PRM Rev 0.7

www.coolautomation.com

0.5ºC

1ºC

MD,CG,KT,TR

1ºC

The deg setting (see

set

command) defines which temperature scale Celsius or Fahrenheit is used for <TEMP>

and <TEMP.d> parameters value.

EXAMPLE

Set Indoor Unit 102 on line L1 Set Temperature to 23º

temp L1.102 23

Decrease all Indoor Units on line L2 Set Temperature by 2º

temp L2* -2

Set all Indoor Units on line L2 Set Temperature to 24.5º

temp L2* 24.5

Set all Indoor Units Set Temperature to 22º

temp 22

fspeed

SYNOPSIS

fspeed [

UID

] <v,V|l,L|m,M|h,H|t,T|a,A>

DESCRIPTION

Set Indoor Unit(s) Fan Speed to:

v, V - very low or quiet

l, L - low

m, M - medium

h, H - high

t, T - top or very high

a, A - auto

Not all Indoor Units support Fan Speed options listed above. Specific Fan Speeds support depend on specific
Indoor Unit capabilities. If requested Fan Speed is not supported by Indoor Unit(s) fspeed command will have
no effect.

EXAMPLE

Set Indoor Unit 102 on line L1 Fan Speed to low

fspeed L1.102 l

Set all Indoor Units on Line L2 Fan Speed to high

fspeed L2* h

Set all Indoor Units Fan Speed to medium

fspeed m

Содержание CoolMasterNet
















































Результаты поиска

Содержание CoolMasterNet

Отзывы:

CoolAutomation CoolMasterNet, Руководство пользователя, Страница: 36 / 47

Результаты поиска

Содержание CoolMasterNet

Отзывы: