manualshive.com logo in svg

CoolAutomation CoolMasterNet, Руководство пользователя, Страница: 20 / 47

Поделиться
Скачать
CoolAutomation CoolMasterNet Скачать руководство пользователя страница 20

ASCII I/F

CoolMasterNet PRM   Rev 0.7

20

www.coolautomation.com

© 2017 CoolAutomation

DESCRIPTION

Query or change 

HVAC Line

(s) status and configuration. In format without parameters 

l i n e

 command will

provide information about current Line statuses. Second format is used to change write enabled properties. 

<PROPERTY>

Mode Value

Description

Notes

master

R/W

0 or 1

CoolMasterNet acts as a Master device

DK, LG, SA, TO,
PN
only

simul

R/W

integer

Simulate given number of Indoor Units. To disable simulation use
"0". Simulation is persistent (not disabled after power reset)
By default the simulation model is: with failures, no ventilation
units, no input/output units. To enable/disable special conditions
use the following flags: 
+/-flr, +/-vam, +/-io (see example)

Input/Output units
for ME only
Ventilation units
for DK, ME, LG
only

myid

R/W

string

CoolMasterNet Own address on given HVAC Line. 
For ModBus RTU Line myID is a "Slave Device Address"

baud

R/W

Configure UART parameters for given Line. Value format is:
<BAUD> <8|9><N|E|O><1|2>
For example: 9600 8N1

Where applicable

Tx

RO

integer

counter

Transmitted messages

Printed as 
Last/Total
Last means since
previous print 

Rx

RO

Received messages

TO

RO

Timeout errors

CS

RO

Checksum errors

Col

RO

Collision errors

NAK

RO

NAK errors

haux

R/W

heat or

haux

Heat mode treated as Haux mode. This is only for situation when
HomeAutomation controller doesn't have Haux support, but need
to set Haux mode on ThermoPad(s)
connected to CH line.

For CoolHub
(CH) line only

type

R/W

string

Define line type by 

acronym

. Number of HVAC lines cannot

exceed the value of HVAC lines in 

set

 command.

HomeAutomation/BMS lines don't count as HVAC Lines.
To free a line use Unused instead of acronym.

See the full list
of 

HVAC

 and

HomeAutomatio
n/BMS

 lines

supported

scan

R/W

0 or 1

Implicitly detect Indoor Units

ME, HT, SA, TO,
PN only

DCOUT

R/W

- or +

Control DC output on L1,L2

DK,ME only

slink

R/W

O/o or

N/n

Configure Mitsubishi Heavy SuperLink mode: O - old, N -
new

MH only

Configure Samsung model type: O - DVM,  N - DVM-S

SM only

[A|B] or [B|A]

RO

Current polarity

Line L7 only

EXAMPLE

>

line                                                            

  L1: SA U00/G02 myID:E5                                         
   Tx:732/732 Rx:47227/47227 TO:0/0 CS:0/0 Col:0/0 NAK:0/0       
  L2: DK Master U00/G07 myID:0B                                  
   Tx:4579/4579 Rx:50633/50633 TO:3/3 CS:0/0 Col:10/10 NAK:0/0   
  L3: Unused                                                     

Содержание CoolMasterNet
















































Отзывы:

Нет отзывов