Contronics Remote-i Net Скачать руководство пользователя страница 18

Remote-i Net

5. The COMMUNICATION LED remained red for some time without flashing and now it is

flashing orange. What should be done?

This is an indication that something has gone wrong in the process of connection between the

Remote-i Net

 and the remote computer. 

The most probably reasons for this signaling are:

a.

faulty contact of the

 Remote-i Net 

network cable

b. the remote computer was switched off
c. the remote computer is no longer accessible on the local network
d. the 

CommCenter 

program, which waits for the remote computer downloads, was

disconnected 

e. the connection between the 

Remote-i Net

 and the remote computer is experiencing traffic

problems, possibly on the Internet 

Carry out a verification of each one of these items. If it is a temporary problem, just remove the

Guardus

 from the 

Remote-i Net

 metal receptacle until the COMMUNICATION LED goes off and

try again. A new attempt will be started as soon as the 

Guardus

 is replaced on the metal receptacle.

If the problem remains, enter into contact with the person responsible for your local network, so
that the source of the problem can be verified.

6. The COMMUNICATION LED is red without flashing. Is it OK to remove the Guardus from the

Remote-i Net metal receptacle?

No. While the COMMUNICATION LED is lit in red the

 

Remote-i Net

 

will be processing the

Guardus 

data download and should not be interrupted. Wait until this LED changes to green

(without flashing) or to orange (flashing) before removing the

 Guardus

.

7. The COMMUNICATION LED is green without flashing. Is it OK to remove the Guardus from

the Remote-i Net metal receptacle?

Yes. When the COMMUNICATION LED remains green without flashing it means that the data
which were stored on the 

Guardus

 were downloaded onto the remote computer successfully. This

LED will only go off when the 

Guardus

 is removed from the metal receptacle.

8. I will use Remote-i Net only on an internal network, where my PC which runs CommCenter is in

the room next door.  Which type of configuration do I need? 

You need to configure the (Guardus G or Guardus T) using the corresponding application for it to
store the network address of the PC where the CommCenter program is running. If you do not know
the PC address, ask your network administrator.  

The steps to program the wand are as follows: 
a. Carry out a new download or open a previous download;

14

Contronics

Содержание Remote-i Net
























Отзывы: