manualshive.com logo in svg

Control Techniques UD53, Руководство пользователя

Поделиться
Скачать
Control Techniques UD53 Скачать руководство пользователя страница 5

UD53 User Guide
Issue code:   53nu3

1

1

Introduction

1.1 

Main features of the UD53

Applications

The UD53 Resolver 

small option module

 is an interface module for

installation in a Unidrive.   The UD53 operates with resolvers having the
following specifications:

Input impedance:   >85

Ω

 at 6kHz

Turns ratio (primary:secondary):   3:1 or 2:1

Excitation voltage:   6V

RMS

 or 4V

RMS

The Drive must be operating in the Closed-loop Vector or Closed-loop
Servo mode; the resolver connected to the UD53 is used for speed and
position feedback.

Simulated
encoder
outputs

 The simulated-encoder outputs produce 

quadrature AB

 signals

corresponding to the 

line counts

 from the source encoder.   Alternatively,

these outputs can be configured for frequency and direction (F/D) signals.
In both cases, the outputs retain position infomation when direction is
changed.

By default, the resolver is used as the source for the simulated-encoder
outputs; alternatively, the main encoder (Encoder 1) connected to the
15-way D-type on the Drive can be used as the source.

The number of pulses per revolution can be scaled by factors of 2.

Installation

The UD53 must be fitted in the 

small option module

 bay of the Unidrive.

All connections to the Drive are made by a multi-way connector.  
Connections from external equipment are made by a plug-in 16-way
screw-terminal block on the UD53.

Содержание UD53



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды