manualshive.com logo in svg

Control Techniques UD53, Руководство пользователя

Поделиться
Скачать
Control Techniques UD53 Скачать руководство пользователя страница 15

UD53 User Guide
Issue code:   53nu3

11

Procedure

1 

Ensure the motor is unloaded (any load will create errors in the
phase-offset measurement).

2 

Set parameter 

16.05

 

Resolver phasing test

 at 1.

3 

Enable the Drive.

 

The motor shaft rotates (as described before this procedure) and the
measured value of phase offset is automatically entered in parameter

16.09

 

Resolver phase offset.

   The motor shaft should rotate clockwise;

if it rotates anti-clockwise, reverse  two of the phase connections from
the Drive to the motor.

 

If a phasing test is attempted with a motor that has high inertia, no
damping or a small load on the shaft, an incorrect value for the phase
offset will be measured.   Refer to parameter 

5.27

 in the 

Unidrive

Advanced User Guide

.

Note

If the Drive trips and the display indicates trip code
ENC.PH7, this indicates either of the following:

The 

SIN

 and 

COS

 connections from the resolver are

incorrectly made
The phase sequence of the motor is reversed

Correct the connections and repeat the procedure.

Magnetizing current test (Closed-loop Vector)

Refer to 

Autotune

 in Chapter 3 

Setting Up the Drive

 in the 

Unidrive User Guide

,

or to parameter 

5.12

 in the 

Unidrive Advanced User Guide

.   If the Drive trips

while Autotune is being performed, see the Note above.

Содержание UD53



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды