manualshive.com logo in svg

Control Techniques SM-Encoder Plus, Руководство пользователя

Поделиться
Скачать
Control Techniques SM-Encoder Plus Скачать руководство пользователя страница 33

SM-Encoder Plus User Guide

33

Issue Number:  3

www.controltechniques.com

Any trip can be initiated by writing the relevant trip number to Pr 

10.38

. If any trips 

shown as user trips are initiated the trip string is "txxx", where xxx is the trip number.
Trips can be reset after 1.0s if the cause of the trip has been rectified.
A full list of drive trips can be found in the 

Unidrive SP User Guide.

Table 7.1 Trip codes

Trip

Diagnosis

C.Optn

SMARTCARD trip: Solutions Modules fitted are different between source drive 
and destination drive 

180

Ensure correct Solutions Modules are fitted 
Ensure Solutions Modules are in the same Solutions Module slot
Press the red 

 reset button 

Enc1

Drive encoder trip: Encoder power supply overload

189

Check encoder power supply wiring and encoder current requirement
Maximum current = 200mA @ 15V or 300mA @ 8V and 5V

PS.24V

24V internal power supply overload

9

The total user load of the drive and Solutions Modules has exceeded the internal 24V 
power supply limit.
The user load consists of the drive’s digital outputs plus the SM-I/O Plus digital 
outputs, or the drive’s main encoder supply plus the SM-Universal Encoder Plus 
encoder supply.
•

Reduce load and reset

•

Provide an external 24V >50W power supply

•

Remove any Solutions Modules and reset

SLX.dF

Solutions Module slot X trip: Solutions Module type fitted in slot X changed 

204,209,

214

Save parameters and reset

SLX.Er

Solutions Module slot X trip: Error detected with Solutions Module, where X is 
the slot number 

202
207
212

# - If the terminations are not enabled on the A, B or Z inputs the wire break system will 
not operate. (Note that as default the Z input terminations are disabled to disable wire 
break detection on this input.)
Encoder initialisation will occur when trips 1 to 8 are reset. 
It is important that a break in the connections between the drive and the position 
feedback device can be detected. This feature is provided either directly or indirectly 
as listed.
When the drive is reset this parameter is cleared for the relevant Solutions Module

Pr x.50 Fault description

0

No errors

1

Power supply short circuit

2

Hardware detectors on the A(F), B(D,R) and Z signal detect a wire break.

9

Thermistor trip

10

Thermistor short circuit

74

Solutions Module over-temperature

Содержание SM-Encoder Plus







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды