background image

Inside Panel Description

Figure 2. Door Station, Inside Panel

AC connection

. Used to connect the wires for AC 

power.

DC connection

. Used to connect the wires for DC 

power.

Contacts/Relays

. Used to connect the wires for 

Control4 and third-party devices.

NOTE:

 Use the contacts and relays for non-

secure devices only. For example, don’t attach 
security gate wires to this terminal block.

Ethernet connection

. Supports PoE.

Reset Button

. Used to reset or factory restore the 

Door Station.

Door Station - Exterior  

Setup Guide  

Pre-Installation
   

Find the best exterior location for the Door 
Station. See “Mounting Tips” below.

Install the Door Station Back Box. See the 

Door 

Station Back Box Installation Guide

 for details.

Determine which network and power options 
to use (see “Network Options” and “Power 
Options”).

(WiFi only). Before the Door Station is fully 
installed, Control4 recommends to test the 
WiFi signal strength in Composer Pro’s System 
Manager; a strong, robust signal is required. See 
the 

Composer Pro User Guide

 for details.

This device uses an Ethernet or WiFi network 
connection and can be powered using Power 
over Ethernet (PoE), AC, or DC.  A wired network 
connection is recommended for the best Video 
Intercom experience.  If it is not possible to use 
Ethernet, then please follow these guidelines for 
wireless.

NOTES

: (1) Video Intercom usage. Although 

this device supports b/g/n, 802.11 b is not 
recommended or supported for Video 
Intercom. (2) Wireless-N is recommended 
for Video Intercom. See “Wireless Network 
Limitations” below.

Wireless Network Limitations

Many WiFi Access Points handle Multicasts 
(WiFi simultaneously sent to multiple devices, 
for example, when the Door Station broadcasts 
video to all stations) by slowing down 
transmission speed to the 1 Mb basic rate. This 
can cause overall WiFi congestion in the WiFi 
network during the broadcast. Video Intercom 
response times and images may degrade at 
each device. 

If a home requires a large number of WiFi 
Video Intercom devices, ensure that you have 
a robust WiFi network (possibly consisting of 
multiple access points).

2

3

5

2

4

4

4

4

4

4

4

4

4

4

4

4

1

Содержание C4-DSC-EN-BL












Отзывы: