background image

Evora-SP60

 - 60W LED compact moving head with motorized focus and prisms

Page 17

English

Once switched on the unit will launch an initialisation. The display will indicate "XXEr" if a problem occurs 
with one or several channels. If a problem occurs on channel 1 the display will indicate « 01Er » , « 02Er » 
for channel 2, and so on.
If you encounter problems with channel 1, 2 and 5, the following message will be indicated: « 01Er », 
« 02Er », « 05Er ». It will flash 5 times. The device will then reset and all motors will go back to their initial 
position. If the message keeps ocurring after 3 resets, there are more than 3 errors. The channels cannot 
operate properly if there are more than 3 errors. If less than 3 errors, the concerned channels will be 
deactivated but the projector can be operated.

 : Colour wheel error.

This message appears after the initialisation of the unit if the magnetic position sensor of the colour wheel 
is defective or misplaced.

 : Gobo wheel error.

This message appears after the initialisation of the unit if the magnetic position sensor of the gobo wheel 
is defective or misplaced.

  : Gobos indexation error.

This message appears after the initialisation of the unit if the magnetic position sensor of the gobo 
indexation is defective or misplaced.

 : PAN (yoke) movement error.

This message appears after the initialisation of the unit if the magnetic position sensor of the PAN 
movement is defective or misplaced.

 : TILT (head) movement error.

This message appears after the initialisation of the unit if the magnetic position sensor of the TILT 
movement is defective or misplaced.

 : Error on the prism channel.

This message appears after the initialisation of the unit if the magnetic position sensor of the prism is 
defective or misplaced.

 : Error on the focus channel.

This message appears after the initialisation of the unit if the the magnetic position sensor of the prism is 
defective or misplaced.

Errors may have various origins. Sensors are used to set the motors in their default position.
Either the magnetic sensors are defective, or the magnets have been displaced.
Problems might also come from a defective motor or the motor electronic management.
In any case, please write down the error displayed and contact your retailer to launch a maintenance 
procedure.

Do NOT attempt to repair it by yourself as only Contest-approved technicians are allowed to perform 
maintenance operations.

10 - Error messages

Содержание Evora SP60





















Отзывы: