Constructor CTJS802PLA-BM, Оригинальное руководство пользователя

Страница: 22 / 41

22
ELECTRONIC SPEED CONTROL SETTING
Turn the knurled screw in PLUS direction for a
higher speed and turn it in MINUS direction for
a lower speed.
The ideal cutting rate depends on the specific
material and working conditions.
The general rules for tool speed in cutting
operations apply.
See turn the speed controller to increase the cutting
rate.
ADJUSTING THE BASE
For mitre and bevel cuts you can swivel the base by
up to 45° in either direction after undoing the two
screws on the bottom The angles 15°, 30° an d 45°
are marked but you can adjust the saw to any angle
between these markings as required.
To adjust the cutting angle, undo the two screws
until you can just about move the blade. Adjust to
the required angle and re-tighten the two screws.
To enable you to saw right up to the edge, the base
can be pushed backward. To do so, undo
the two screws underneath and push the base to
the back. Re-tighten the two screws.
Undo the two screws to set the base to an angle of
0° to 45° on the right or left side.
MOUNTING THE PARALLEL GUIDE
The parallel guide allows sawing parallel to an edge
at a maximum distance of 10 cm.
Insert the parallel guide into the saw base as
shown in the illustration.
Set the parallel guide to the required distance and
tighten the locking bolts.
USING THE PENDULUM ACTION SWITCH
The pendulum action switch is used to set the
correct sawing angle for the material.
Turn the switch (8) to the required pendulum
action position. Refer to the table below for the
correct pendulum action position for different
materials.
Material Pendulum action position
Wood I-III
Plastic I
Aluminium 0-I
Steel 0
Ceramics 0
Rubber 0
INSTRUCTIONS FOR USE
Clamp the workpiece. Make sure that the side
which will be visible later is facing down, because
the cut is most accurate at that side.
Make sure that the saw blade has reached full
speed before it touches the workpiece.
Do not exert pressure on the saw blade. Allow the
machine enough time to cut the workpiece.
For sawing along a drawn line use the marking .
Switch off the machine and wait for the saw blade
to come to a standstill before putting the machine
down.
SWITCHING ON AND OFF
To switch on the machine press the on/off switch
(1).
To adjust the cutting speed, turn the adjusting
wheel (3).
To switch off the machine, release the on/ off
switch (1).
To switch the machine to continuous mode, you
keep the on/off switch (1) fully pressed and
simultaneously press the lock button (2). And
subsequently release the on/off switch.
To switch off continuous mode, press the on/off
switch (1) again.
When sawing metal always
use a coolant (for example
oil or water) to prevent the
machine and work piece
from overheating.
USING THE LASER AND LED-LIGHT (10)
You can use LED-light to enlighten the approximity
of the cutting position.
The laser beam projects a red cutting line on the
workpiece.

Switch the laser on by means of the on/off
switch.

Place the machine on the workpiece with the
saw marking above the start of the cutting line.

Check that the laser line aligns with the
cutting line as marked on the workpiece.

Switch on the machine.

Follow the “Instructions for use” to perform a
cut.

After use, switch off the laser.
TRANSFER SWITCH FOR WIND DIRECTION (11)
Slide the transfer switch forward to change the wind
direction forward as the arrow that avoid sawdust
cover previously marked line on the work-piece
which it’s convenient for moving the tool forward
along previously marked line.
DUST EXTRACTION
The dust extraction connection (9) together
with an external vacuum cleaner takes care
of the dust extraction of the working surface.

Slide the suction mouth of a vacuum
cleaner onto the connection (9).
CLEANING AND MAINTENANCE
Attention! Before
performing any work on
the equipment, pull the
power plug.
Service
§ Only qualified specialist personnel and original
replacement parts should be used for repairs. This
will ensure that your device remains safe.
Cleaning
§ Regularly clean the machine housing with a soft
cloth, preferably after each use. Keep the
ventilation slots free from dust and dirt. If the dirt
does not come off use a soft cloth
moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water,