Congatec COM Express conga-MEVAL Скачать руководство пользователя страница 26

Страница: 26 / 58

2022

congatec

GmbH

CET0m10

26/58

5.4.1

PCIe x4 Slot

The conga-MEVAL provides a standard PCIe x4 slot connector X74 (Slot 0). This slot, which is routed to the module’s PCIe lanes 0–3, shares:

•

PCIe lane 1 with connector X8 (Slot 1)

•

PCIe lane 2 with connector X15 (mPCIe slot)

•

PCIe lane 3 with connector X84 (Slot 2)

PCIe Slot 0 supports one PCIe lane (x1 link) by default. To support x4 link operation, set jumper X75 as described in the table below:

Table 14 X75 - PCIe x4 Slot Configuration

Description

1-2

x1 PCIe link (default)

2-3

x4 PCIe link

Note

The COM Express module must support the selected PCIe configuration.

Connector Type

X74: PCIe card

X75: 2.54 mm grid jumper

5.4.2

PCIe x1 Slot

The conga-MEVAL provides two standard PCIe x1 slots. The table below shows how the signals are routed to the connectors:

Table 15 PCIe x1 Lane Routing

Slot Number

PCIe Lane

Connector

Slot 1

PCIe 1

Slot 2

PCIe 3

X84

X75

X74

X8, X84

Содержание COM Express conga-MEVAL

























































Результаты поиска

Содержание COM Express conga-MEVAL

Отзывы:

Похожие инструкции для COM Express conga-MEVAL

Бренды по названию

Популярные бренды

Congatec COM Express conga-MEVAL, Руководство пользователя

Результаты поиска

Содержание COM Express conga-MEVAL

Отзывы:

Похожие инструкции для COM Express conga-MEVAL

Бренды по названию

Популярные бренды