Congatec COM Express conga-MEVAL Скачать руководство пользователя страница 41

Страница: 41 / 58

2022

congatec

GmbH

CET0m10

41/58

5.10.1

Audio Jacks

The conga-MEVAL supports the audio outputs described in the table below.

Table 35 CN2 Pinout Description

Jack 1 (Orange)

Signal

Description

Jack 4 (Blue)

Signal

Description

Tip

MIC_L

Microphone - left channel

Tip

LINEIN_L

Line input 1 left

Ring

MIC_Bias

Microphone bias voltage

Ring

LINEIN_R

Line Input 1 right

Sleeve

A_GND

Analog ground

Sleeve

A_GND

Analog ground

Jack 2 (Black)

Signal

Description

Jack 5 (Lime)

Signal

Description

Tip

LINEOUT_L2 Line output 2 - left channel

Tip

LINEOUT_L1 Line output 1 - left channel

Ring

LINEOUT_R2 Line output 2 - right channel

Ring

LINEOUT_R1 Line output 1 - right channel

Sleeve

A_GND

Analog ground

Sleeve

A_GND

Analog ground

Jack 3 (Grey)

Signal

Description

Jack 6 (Pink)

Signal

Description

Tip

HPOUT_L

Headphone output - left channel Tip

MIC_L

Microphone - left channel

Ring

HPOUT_R

Headphone utput - right channel Ring

MIC_R

Microphone - right channel

Sleeve

HPREF

Headphone ground reference

Sleeve

A_GND

Analog ground

Note

The optional orange jack is not supported by default (assembly option)

Hardware revision C.x and earlier do not support microphone input on jack 6 (pink)

Note

The Windows OS driver is available in the product section (under accessories) of the congatec website at www.congatec.com.

Connector Type

CN2: Six 3-pin, 3.5 mm audio jacks

CN2

Jack Pins

Tip

Ring

Sleeve

Содержание COM Express conga-MEVAL

























































Результаты поиска

Содержание COM Express conga-MEVAL

Отзывы:

Похожие инструкции для COM Express conga-MEVAL

Бренды по названию

Популярные бренды

Congatec COM Express conga-MEVAL, Руководство пользователя

Результаты поиска

Содержание COM Express conga-MEVAL

Отзывы:

Похожие инструкции для COM Express conga-MEVAL

Бренды по названию

Популярные бренды