PARTS LIST
4 - Handrail / Leg
1 - Deck Platform
2 - Bottom Tread
8 - Upper Tread (Slip-on Style)
2 - Adjustable Brace
1 - Tread Connector (Left Hand)
1 - Tread Connector (Right Hand)
MODEL # 7000
“ELIMINATOR” A-FRAME LADDER
ADJUSTABLE to fit 48” TO 54” ABOVE GROUND POOLS
HARDWARE PACK
26 - #10 x 1-1/4" Screw
2 - 1/4-20 x 3-1/4" Bolt
6 - 1/4" Washer
2 - 1/4" Nylon Nut
2 - 1/4-20 x 2-1/4" Bolt
2 - 1/4" Hex Nut
4 - Push in Plug
1 - Cable Lock Set
IMPORTANT: Remove the wedges from the
deck platform protrusions and SAVE
for step 5.
Slide the handrail/ legs
together as shown.
Apply liquid soap or
spray lubricant to aid
assembly.
Tools required for assembly:
Hammer or mallet, Cordless drill motor, 1/8" & 9/32" drill bits, Phillips screwdriver bit. Pliers, 7/16" wrench or adjustable
wrench.
Twist and save.
Pliers may be
useful to aid in removal.
Step 3.
Place one handrail/leg assembly on a clean flat surface
and push the deck platform protrusions in the openings.
Step 4.
Repeat the process with the second handrail/leg assembly,
pushing firmly down onto the deck protrusions to ensure a
secure fit.
Step 8.
Step 5.
Insert the four wedges that were saved from step 1
into the top of the openings as shown.
Insert wedges
Step 7.
Slide the three remaining upper treads into
position in the ladder legs. Position the right
and left hand tread connectors onto the ends
of the treads and fasten them to the ladder
legs, through the pre-formed holes, using two
1/4-20 x 3-1/4" bolts four washers and two
nylon nuts (as shown in exploded diagram).
Tighten securely but do not overtighten. Attach
the tread connectors to the ends of each tread
using #10 x 1-1/4" screws (four per tread).
Step 9.
Step 10.
Attach
Bottom
treads
Stand here
Stand here
Push down firmly.
Push down firmly.
3
2
Step 6.
Slide five upper
treads into position
so they are resting
on the double nubs
of the legs (as
shown in diagram).
Secure the treads
to the legs using
#10 x 1-1/4" screws
(two per tread)
through the
pre-drilled hole.
Do not
attach the
three
remaining
upper
treads to
the legs.
Tread connectors
1/4” Nylon Nut
1/4”-20 x 3-1/4”
Bolt
1/4" Washer
TILT
Locate the ladder at the desired
position on the pool and place one
of the adjustable braces on the side
of the ladder so that it rests on the
top of the pool. Secure the
adjustable brace to the ladder with
two #10x 1-1/4" screws. Repeat for
other brace.
Note: the adjustable
braces are not needed if the deck
platform of the ladder rests on the
top of the pool.
Using the braces as locators (or the
deck platform), drill two 9/32" holes
through the pool top seat. Be care-
ful not to damage liner or pool wall.
Fasten the ladder to the pool top
using the two 1/4-20 x 2/1/4" bolts,
washers and hex nuts.
26 2
6
2
2
2
4
Step 1.
Step 2.
Stand on one of the upper
treads to snap the legs into
the bottom tread.
Nubs
Place the ladder
in the pool and fill
legs with water
through the openings
with a hose. Then
plug the holes using
the four push in
plugs. Tilt it so the air
is released from all
the submerged
treads.
(Not To Scale)
Step 8a.
Please refer to the separate instruction sheet for anti-entrapment barrier installation.
Confer 7000_9_04 9/23/04 2:58 PM Page 3
