Condair Modbus RTU Скачать руководство пользователя страница 39

Страница: 39 / 61

Modbus Installation |

Control Signal Setting

By default the humidifier is configured operate on a hardwired control signal supplied through
the unit terminal strip. This can be changed to allow the humidifier to function entirely through
its Modbus interface.

To adjust this setting:
1

Press the

Menu

key to access the menu.

Select the

User

options and press

Set

When prompted for a password, enter 8808 using the arrow keys. Confirm the password
with set.

Select the

Controls

menu and press the

Set

key. The following settings can be adjusted:

Signal Source

Analog:

Use hardwired control signal

Modbus:

Write control signal through Modbus interface

Hum. Control

External

: Use a demand control signal

Int(p)

: Use a sensor value and proportional

int(pi)

: Use a sensor value and proportional-integral control band

Control Sign

Setting not relevant when writing control signal through Modbus.

Note: Refer to the

MHTC Humidifier Configuration

section of the MH Series Installation and

Operation Manual for more information on the above settings.

1

Press

Esc

repeatedly to return to the home screen when complete.

This procedure is summarized below:

Menu > User > 8808 > Controls >

Signal Source: Analog or Modbus
Hum. Control: External, Int(p), or Int(pi)
Control Sign: As required

Содержание Modbus RTU






























































Результаты поиска

Содержание Modbus RTU

Отзывы:

Похожие инструкции для Modbus RTU

Бренды по названию

Популярные бренды

Condair Modbus RTU, Руководство по эксплуатации

Результаты поиска

Содержание Modbus RTU

Отзывы:

Похожие инструкции для Modbus RTU

Бренды по названию

Популярные бренды