CONCORD NT30 Скачать руководство пользователя

Страница: 80 / 150

3.16.4 Opening disc offset

The opening disc offset is the amount of offset (A)

between the two opening discs (1) on each toolbar.

The opening disc offset prevents material from

accumulating between the two opening discs on

the opening disc assembly.
The opening disc offset is set at 114 mm (4.5 inch)

at the factory, but can be adjusted from 38 mm to

165 mm (1.5 to 6.5 inch).
Increase the opening disc offset for wet, sticky

soils.
Decrease the opening disc off set for dry, sandy

soils.

If operating in soil with large rocks, set the

opening disc offset to the maximum offset.

GUID-CF4DC160-9997-4EA3-A0AF-EAF84FD53429-high.jpg [High]

Fig. 40

GUID-E5EAE9EF-74ED-4BB8-8338-FFB678905633-high.jpg [High]

Fig. 41

If the opening disc offset is too wide, there will not

be enough soil movement for sufficient trench

closure.
If the opening disc offset is too narrow, material will

build between the two opening discs.

Use the five sets of holes on one side (1) of the

opener mount to adjust one of the opening discs.

Use the two sets of holes on the opposite side (2)

to adjust the other opening disc offset . Each set of

holes will change the offset by 25 mm (1 inch)(A).

Opening disc offset table

The following table shows the opening disc offset

according to the position of the opening disc struts

(1) on the opening disc mount (2). The first column

shows the number of pairs of holes (3) forward of

the opening disc strut on the five position side of

the opener mount. The second column shows the

position of the opening disc strut on the two

position side of the opener mount, forward or rear.

The third column shows the opening disc offset.

GUID-11F73C71-21F2-4558-945D-63ADD60F5DA2-high.jpg [High]

Fig. 42

GUID-246768DE-8FD7-4DE5-B437-0A6DD829C561 [V3]

3. Operation

Narrow-Transport Grain

Drill (322782B)

Содержание NT30























































































































































Результаты поиска

Содержание NT30

Отзывы:

Похожие инструкции для NT30

Бренды по названию

Популярные бренды

CONCORD NT30, Руководство оператора

Результаты поиска

Содержание NT30

Отзывы:

Похожие инструкции для NT30

Бренды по названию

Популярные бренды