CONCORD NT30 Скачать руководство пользователя

Страница: 22 / 150

crop material and unwanted material from around the area. Make sure that the area below the work area is

clear of flammable material because falling molten metal and sparks can cause ignition in the material.
If fire occurs, move upwind and away from the

smoke from the fire.

GUID-8FDCA67C-244A-40BA-967B-3FA4E7667A7E-high.jpg [High]

Fig. 19

1.4.3 High pressure leaks

WARNING: Hydraulic fluid under

pressure can penetrate the skin or

eyes.
Serious personal injury, blindness, or

death can occur.
Relieve the pressure from the system

or component before disconnecting

components. Wear personal

protective gear while working on the

machine or equipment. Use a piece of

cardboard to check for leaks. Never

use your hand.

GUID-CB450E2E-50DF-4D16-9E59-21C0B3E5B026-high.jpg [High]

Fig. 20

Fluid that leaks from the hydraulic system or the

fuel injection system is high pressure and is not

easily seen. The fluid can go into the skin causing

injury.
Fluid that is injected into the skin must be

surgically removed immediately. If not removed

immediately, infection and reaction can occur. Go

immediately to a physician who knows about this

type of injury.

Use a piece of cardboard or wood to look for

possible leaks. Do not use your bare hand. Wear

leather gloves for hand protection and safety

goggles for eye protection.
Remove all pressure before you loosen hydraulic

lines. Lower equipment in the up position, close

the accumulator valve, and stop the engine.

Tighten all connections before you apply pressure.

GUID-9A83C5CD-95EC-445B-A3A7-1DCF8FACFE45-high.jpg [High]

Fig. 21

GUID-68111A90-0641-4B8F-9AB9-A5B05A044C46 [V4]

1. Safety

Narrow-Transport Grain

Drill (322782B)

Содержание NT30























































































































































Результаты поиска

Содержание NT30

Отзывы:

Похожие инструкции для NT30

Бренды по названию

Популярные бренды

CONCORD NT30, Руководство оператора

Результаты поиска

Содержание NT30

Отзывы:

Похожие инструкции для NT30

Бренды по названию

Популярные бренды