background image

 

Page 

10

 of 

16

 

 
 
Use the upper support point for 1000ml bags  
 
and 
 
the lower support point for 500ml bags. 
 
 
 

 
Carefully locate the bag neck in the cradle (1).  Close the retaining gate and insert the retaining 
screw (2).  Ensure the bag neck is held correctly and the fluid micro switch is activated properly. 
 
 
 
 
 
 
 
 
 
 
 
 
 

ALWAYS REPLACE A FULL FLUID BAG OR 5000ML BOTTLE EVERY TIME THE FLUID BAG 
HOLDER MICRO SWITCH IS RESET.  FAILURE TO DO SO MAY RESULT IN DAMAGE TO THE 
SMOKE FLUID PUMP. 
 
WHEN A NEW FLUID BAG IS FITTED POWER MUST BE APPLIED TO THE SMOKE SCREEN TO 
RESET THE FLUID TIMER. 
 

BATTERY MANAGEMENT

 

 

Operation.

  The Smoke Screen is fitted with a battery to provide power to the electronic circuits 

and pump (not to the fluid heater) in the event of a mains power failure.  This ensures that 1 hour 
after a mains power failure at an ambient temperature of 20 deg C the Smoke Screen can provide 
a 20 second activation.  The Smoke Screen is capable of activating in the event of a battery fault or 
if the batteries are not fitted; in the latter case, to avoid battery fault indications, the facility should 
be disabl

ed (see section under “Programming”).  The Smoke Screen is supplied with a set of 

batteries but they are not fitted on delivery.  Replacement batteries may be obtained from your 
Smoke Screen installer or Concept Smoke Screen. 
 

Removal and replacement.

  To remove the batteries, open the access panel on 

the left side of the Smoke Screen.  Slide out the old batteries and replace with 
new units ensuring that the battery is upright and the contacts enter the battery 
compartment first. 

 
Battery Switch.

  Later models (post serial number 1013301) of the Smoke 

Screen have a switch in the battery compartment to permit the batteries to be 
disconnected from the system whilst remaining in place.  The delivery setting is 
“Off”; select to “On” if intending to use the battery facility. 

 
 
THE SMOKE SCREEN WILL NOT FUNCTION AT ALL DURING A MAINS POWER FAILURE IF 
THE BATTERIES ARE DISABLED. 

 

Содержание Sentinel S70

















Отзывы: