Comtrend Corporation WAP-EN1200 Скачать руководство пользователя страница 61

Страница: 61 / 110

5GHz WDS Mode

WDS Functionality

Select “WDS with AP” to use WDS with access

point or “Dedicated WDS” to use WDS and also

block communication with regular wireless

clients. When WDS is used, each access point

should be configured with corresponding MAC

addresses, wireless channel and wireless

encryption method.

Local MAC Address

Displays the MAC address of your access point.

WDS Peer Settings

WDS #

Enter the MAC address for up to four other

WDA devices you wish to connect.

WDS VLAN

VLAN Mode

Specify the WDS VLAN mode to “Untagged

Port” or “Tagged Port”.

VLAN ID

Specify the WDS VLAN ID when “Untagged

Port” is selected above.

WDS Encryption

Encryption

Select whether to use “None” or “AES”

encryption and enter a pre-shared key for AES

with 8-63 alphanumeric characters.

IV-3-2-5. Guest Network

The “Guest Network” page allows you to configure a guest network that will

have a Layer-3 IP Filter applied to all traffic passing through the specific SSID.

When using a Guest Network, Traffic Shaping and IP Filter

settings will be applied to all traffic passing through the Guest Network

SSID.

Содержание WAP-EN1200















































































































Результаты поиска

Содержание WAP-EN1200

Отзывы:

Бренды по названию

Популярные бренды

Comtrend Corporation WAP-EN1200, Руководство пользователя

Результаты поиска

Содержание WAP-EN1200

Отзывы:

Бренды по названию

Популярные бренды