Comtrend Corporation WAP-EN1200 Скачать руководство пользователя страница 105

Страница: 105 / 110

101

V-1-6. Glossary

Default Gateway (Access point):

Every non-access point IP device needs to

configure a default gateway’s IP address. When the device sends out an IP

packet, if the destination is not on the same network, the device has to send

the packet to its default gateway, which will then send it out towards the

destination.

DHCP:

Dynamic Host Configuration Protocol. This protocol automatically gives

every computer on your home network an IP address.

DNS Server IP Address:

DNS stands for Domain Name System, which allows

Internet servers to have a domain name (such as www.Broadbandaccess

point.com) and one or more IP addresses (such as 192.34.45.8). A DNS server

keeps a database of Internet servers and their respective domain names and

IP addresses, so that when a domain name is requested (as in typing

"Broadbandaccess point.com" into your Internet browser), the user is sent to

the proper IP address. The DNS server IP address used by the computers on

your home network is the location of the DNS server your ISP has assigned to

you.

DSL Modem:

DSL stands for Digital Subscriber Line. A DSL modem uses your

existing phone lines to transmit data at high speeds.

Ethernet:

A standard for computer networks. Ethernet networks are

connected by special cables and hubs, and move data around at up to 10/100

million bits per second (Mbps).

IP Address and Network (Subnet) Mask:

IP stands for Internet Protocol. An IP

address consists of a series of four numbers separated by periods, that

identifies a single, unique Internet computer host in an IP network. Example:

192.168.2.1. It consists of 2 portions: the IP network address, and the host

identifier.

The IP address is a 32-bit binary pattern, which can be represented as four

cascaded decimal numbers separated by “.”: aaa.aaa.aaa.aaa, where each

“aaa” can be anything from 000 to 255, or as four cascaded binary numbers

separated by “.”: bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each “b”

can either be 0 or 1.

Содержание WAP-EN1200















































































































Результаты поиска

Содержание WAP-EN1200

Отзывы:

Бренды по названию

Популярные бренды

Comtrend Corporation WAP-EN1200, Руководство пользователя

Результаты поиска

Содержание WAP-EN1200

Отзывы:

Бренды по названию

Популярные бренды