Comtrend Corporation WAP-EN1200 Скачать руководство пользователя страница 107

Страница: 107 / 110

103

Application Protocol Port Number
Telnet

TCP

FTP

TCP

SMTP

TCP

POP3

TCP

110

H.323

TCP

1720

SNMP

UCP

161

SNMP Trap UDP

162

HTTP

TCP

PPTP

TCP

1723

PC Anywhere TCP

5631

PC Anywhere UDP

5632

Access point:

A access point is an intelligent network device that forwards

packets between different networks based on network layer address

information such as IP addresses.

Subnet Mask:

A subnet mask, which may be a part of the TCP/IP information

provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured

like an IP address. It is used to create IP address numbers used only within a

particular network (as opposed to valid IP address numbers recognized by the

Internet, which must be assigned by InterNIC).

TCP/IP, UDP:

Transmission Control Protocol/Internet Protocol (TCP/IP) and

Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data

transmission over the Internet. Both TCP and UDP are transport layer

protocol. TCP performs proper error detection and error recovery, and thus is

reliable. UDP on the other hand is not reliable. They both run on top of the IP

(Internet Protocol), a network layer protocol.

WAN:

Wide Area Network. A network that connects computers located in

geographically separate areas (e.g. different buildings, cities, countries). The

Internet is a wide area network.

Web-based management Graphical User Interface (GUI):

Many devices

support a graphical user interface that is based on the web browser. This

means the user can use the familiar Netscape or Microsoft Internet Explorer

to Control/configure or monitor the device being managed.

Содержание WAP-EN1200















































































































Результаты поиска

Содержание WAP-EN1200

Отзывы:

Бренды по названию

Популярные бренды

Comtrend Corporation WAP-EN1200, Руководство пользователя

Результаты поиска

Содержание WAP-EN1200

Отзывы:

Бренды по названию

Популярные бренды