- Double beep and double flash of the green LED indi-
cates that the previous input is correct.
- Enter the new master code (at least 6 maximum
8 digits)
- Press the Button: “ENTER”
- Double beep and double flash of the green LED indi-
cates that the input is correct.
- Enter the new master code (at least 6 maximum
8 digits) again
- Press the Button: “ENTER”
- Double beep and double flash of the green LED indi-
cates that the master code was successfully changed.
- If during the program process you hear a long beep
and the red LED flashes, it indicates that the input is
not correct – the previous master code remains valid
(factory code = 1-2-3-4-5-6)
- After an error message repeat the programming of a
new master code as indicated.
Activate the user code:
Important
We recommend you to perform the programming of a
new user code with opened door several times. Then
check the it works with the door open BEFORE you
close the safe.
- Press the Button: “ON”
- Press the Button: “ENTER”
- Press the Button:”2”’
- Press the Button: “ENTER”
- Enter the valid master code (factory code
1-2-3-4-5-6 ).
- Press the Button: “ENTER”
- Double beep and double flash of the green LED indi-
cates that the previous input is correct.
- Enter the chosen user code (at least 6 maximum
8 digits).
- Press the Button: “ENTER”
- Double beep and double flash of the green LED indi-
cates that the previous input is correct.
- Enter the chosen user code (at least 6 maximum
8 digits) again.
- Press the Button: “ENTER”
- Double beep and double flash of the green LED indi-
cates that the previous the user code was activated.
- A long beep and the flash of the red LED indicates that
the input was incorrect and the user code was not
activated.
- After an error message repeat the programming of the
user code as indicated.
Change the user code:
Important
We recommend you to perform the programming of a
new code with the door open several times. Thereafter
check the correct function of your chosen codes more
times with the door open BEFORE you close the safe.
- Press the Button: “ON”
- Press the Button: “ENTER”
- Press the Button:”3”’
- Press the Button: “ENTER”
- Enter the valid user code.
- Press the Button: “ENTER”
- Double beep and double flash of the green LED indi-
cates that the previous input is correct.
- Enter the chosen user code (at least 6 max. 8 digits).
- Press the Button: “ENTER”
- Double beep and double flash of the green LED indi-
cates that the input is correct.
- Enter the chosen user code (at least 6 max. 8 digits)
again.
- Press the Button: “ENTER”
- Double beep and double flash of the green LED indi-
cates that the user code was successfully changed.
- If during the program process a long beep and the red
LED flashes, this indicates that the input is not correct
and the user code was not changed – the previous user
code remains valid.
- After an error message repeat the programming of the
user code as indicated.
Deleting the user code:
- Press the Button „ON“.
- Press the Button „ENTER“.
- Press the Button „0“.
- Press the Button „ENTER“.
- type in the valid Master code (when new it is
1-2-3-4-5-6).
- Press the Button „ENTER“.
- with a double signal and a double flash of the green
LED you are shown that the user code was success-
fully deleted.
- with a long signal and a red LED you are shown that the
user code has not been deleted.
- after an error report please repeat the procedure as
shown above.
8
FireSafe Electronic ROTTNER TRESOR
07+8+9 GB FireSafe 6.2016_Layout 1 05.07.16 15:34 Seite 8
