COMPX RegulatoR Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 24

COMPX RegulatoR Скачать руководство пользователя страница 18

RegulatoR

®

, Keyless Locking 18

Add User Without Specifying Memory Slot

The Supervisor Code memory location is called Slot 01 and the first User
Code is called Slot 02.

–

Any additional User Codes reside in memory slots 03-20.

–

To add a user code without specifying a memory slot (03 -20), follow
the steps on page 9 to enter programming mode.

User codes must be 4 to 8 digits in length and must be different from all existing
codes (including Slot 01 Supervisor & Slot 02 User codes).

There is a 10 second programming time limit between each step. If RegulatoR
times out or an error is made, programming will end and you will need to enter
programming mode again.

1.

Place RegulatoR into programming mode (see page 9).

2.

Press 410 and then press ENTER.

3.

Type the new user code and press ENTER.

4.

Retype the new user code and press ENTER.

5.

If successful, the yellow indicator light will illuminate.

Continue programming or press 9 and then ENTER to exit programming.

«
...
16
17
18
19
20
...
»

Содержание RegulatoR

























Отзывы:

Нет отзывов