background image

 

Installation Instructions 

MT40-10 

Required Tools 

Wheelbarrow 

Hammer or Mallet 

Shovel 

Open End or Box Wrenches: 5/8”, 9/16”, ¾” 

Digging Bar or Pick 

Ratchet Handle & Sockets: 5/8”, 9/16”, ¾”, 17mm 

Allen Wrench (Provided) 

Marker Pen 

Ladder 

Tape Measure 

Level 

Cordless/Electric Drill w/ the Following Bits: Phillips, 3/8” 

 

PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING 

 

*Before digging, please obey local laws by notifying your local utilities marking 

organization* 

 

1. Select an area in your yard that is reasonably level and meets the space requirement 

for your equipment. Ground Space: 19’ x 15’. Play Space: 23’ x 26’. 

2. Please refer to the top rail assembly sheet and assemble your top rail as instructed.  
3. Position the top rail (see top rail assembly page) about 12’ from the selected spot 

where you want the unit to finally stand. Using a tape measure and marker, mark 
location of the swing hangers and the ladder along the top rail. (See top view on 
assembly and installation instructions for measurements.) 

4. Assemble swing hangers (see swing hanger assembly sheet) and attach securely to 

the top rail.  

5. Using the hammer, install the plug into the open end of the top rail. 
6. Locate position in your yard where the upright ladder will stand. Dig the hole for the 

ladder (see Installation Instruction page #1). Lay the ladder onto the ground with 
the bottom of the ladder laying just over the hole where it will finally stand. Hint: Be 
sure to situate the ladder so that when the unit is finally standing the rungs and the 
third leg bolt will be facing as desired in your space. 

7. Turn the top rail onto its side on the ground. Slide the top rail into the sleeve at the 

top of the ladder and position it to the marks previously made. (see Installation 
Instruction page #3). Loosely install set screws into the top of the ladder sleeve. 

Bolt “A” frame legs into place (see installation instructions page #2). 

8. Using two strong adults, stand the swing frame up, allowing the ladder to fall into 

the hole previously dug. (Note: set will not be level at this point.) At this point, 

check to make sure that the top rail is still in its proper place inside the ladder top 
sleeve. Adjust as necessary by holding onto the ladder securely and pushing or 
pulling the “A” frame section causing the top rail to slide inside the top sleeve. When 

Содержание MT40-10

















Отзывы: