Compliance West HT-2800 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 26

Compliance West HT-2800 Скачать руководство пользователя страница 11

7

Section 3

Operation

This section describes how to set up and make
measurements with your Tester. We recommend
that you read the entire section carefully so that
you can use all of the features of your Tester.

Setting up your Tester

Your Tester is shipped in a special protective
container that should prevent damage to the
instrument during shipping. Check the shipping
order against the contents of the container and
report any damage or short shipment to
Compliance West USA. The container should
include the following:

?

The HT-2800 Dielectric Withstand Tester

?

An 18 AWG Test Lead (Alligator
Clip/Banana Plug ends, black)

?

An 18 AWG Line Power Cord to provide
power to the HT-2800.

?

This Instruction Manual

If reshipment of the instrument is necessary,
please use the original shipping container. If the
original shipping container is not available, be
sure that adequate protection is provided to
prevent damage during shipment. We
recommend that the instrument be surrounded by
at least one inch of shock-absorbing material on
all sides of the container.

Remove the Tester from its container and place it
on a test bench.

AC Line Voltage Requirements

AC line voltage requirements for your Tester are
noted on the rear panel of the instrument. Do not
connect the instrument to a different voltage
source.

Fuse Replacement

There is a user-replaceable fuse (F1) located on
the rear panel of the instrument. It is located
behind a door in the Power Inlet-Power Switch-
Fuse Holder device. The fuse rating is noted on
the rear panel. Do not attempt to replace it with a
fuse of any other rating.

Use the following procedure to replace the fuse
F1:
1.

Turn the power switch to the O or off
position.

2.

Unplug the instrument from the source of
supply.

3.

Remove the power inlet cord from the
instrument.

4.

Using a small screwdriver, pry open the fuse
holder door.

5.

Replace the fuse with a new one of the
correct rating.

6.

Replace the fuse holder door and power inlet
cord.

Front and Rear Panel Features

Before using your Tester, take a few minutes to
become familiar with the use of its controls,
indicators and connectors. The front panel
features of the HT-2800 are shown in Figure 2
and described in Table 2. The rear panel features
of the HT-2800 are shown in Figure 3 and
described in Table 3.

«
...
9
10
11
12
13
...
»

Содержание HT-2800



























Отзывы:

Нет отзывов