background image

Foreword 

Notice

The information in this guide is subject to change without notice.

Compaq Computer Corporation shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of this material.

This document contains proprietary information protected by copyright.

No

part of this document may be photocopied or reproduced in any form with out
prior written consent from Compaq Computer Corporation.

Copyright 1986 by Compaq Computer Corporation.
All rights are reserved.

COMPAQ, COMPAQ PLUS and COMPAQ PORTABLE 286 are registered trademarks and
COMPAQ PORTABLE II is a trademark of COMPAQ Computer Corporation.

The software described in this document is furnished under a license
agreement of nondisclosure.

The software may be used or copied only in

accordance with the terms of the agreement.

It is against the law to copy

Microsoft BASIC or MS-DOS onto cassette tape, fixed disk drive, diskette, or
any other medium for any purpose other than the purchaser's personal use.

Copyright 1981, 1982, 1983, 1984, 1985, and 1986 by Microsoft Corporation.

MS-DOS is a registered trademark of Microsoft Corporation.

MAINTENANCE AND SERVICE GUIDE
COMPAQ PORTABLE COMPUTER
COMPAQ PLUS PERSONAL COMPUTER
COMPAQ PORTABLE 286 PERSONAL COMPUTER

Second Edition (April 1986)
Assembly Number 102901-001
Binder Number 102900-001
Text Number 102973-001

Compaq Computer Corporation 90 Day Limited Warranty

Compaq Computer Corporation (Compaq) warrants the products that it
manufactures to be free from defects in materials and workmanship for a period
of 90 days from the date of purchase from Compaq or an Authorized COMPAQ
Computer Dealer.

This warranty is limited to the original purchaser

(Purchaser) of the product and is not transferable.

During the 90 day (ninety day) warranty period, Compaq will repair or replace
with new or refurbished parts, at its option, any defective parts at no
additional charge, provided that the product is returned, shipping prepaid, to
Compaq or an Authorized COMPAQ Computer Dealer.

The Purchaser is responsible

for insuring any product so returned and assumes the risk of loss during
shipping.

All replaced parts and products become the property of Compaq.

Dated proof of purchase must be provided by the Purchaser when requesting that
warranty work be performed.

The Purchaser may request information on how to

obtain warranty service by contacting an Authorized COMPAQ Computer Dealer or
writing to Compaq Computer Corporation for further information.

Содержание Deskpro 286 - Desktop PC


































































































































Отзывы: