manualshive.com logo in svg

Community ENTASYS 200, Руководство по установке и эксплуатации, Страница: 13 / 28

Поделиться
Скачать
Community ENTASYS 200 Скачать руководство пользователя страница 13

 ENTASYS 200 Installation/Operation Manual — Page 13  

 

Installation 

WARNING:  It is essential that all installation work involving the suspension of these 
loudspeaker products be performed by competent, knowledgeable persons who understand 
safe rigging practices. Severe injury and/or loss of life may occur if these products are       
improperly installed.  

 

DANGER:  It  is  essential  that  a  safety  cable  (not  supplied) be utilized whenever an ENTASYS 
200 is mounted using the supplied Pan-Tilt Bracket. The safety cable must be secured to a 
suitable load-bearing point on the wall or ceiling, with as little slack as possible so as not to 
develop undue kinetic force if the Pan-Tilt Bracket were to fail.  

 

 

FOR MORE INFORMATION 

 

For applications support, service, or warranty information refer to Community’s website, or contact 
one of Community’s TAG personnel (Technical Applications Group ([email protected]) at 
800-523-4934 or 610-876-3400. 

 

 

MODEL 

HI-PASS FREQUENCY 

FILTER SLOPE 

(preferred) 

ENT203

 

 

150 Hz 

24 db / octave 

ENT206

 

 

120 Hz 

24 db / octave 

ENT212

 

 

100 Hz 

24 db / octave 

ENT220

 

 

80 Hz 

24 db / octave 

It is required that an external high-pass filter of 24dB/octave (or steeper) be utilized with all 
ENTASYS 200 systems. The small format, low frequency cone drivers are not capable of reproducing 
high level low frequency information without damage. Recommended high-pass filter parameters are 
shown below: 

EXTERNAL HIGH-PASS FILTERS 

Содержание ENTASYS 200





























Отзывы:

Нет отзывов