manualshive.com logo in svg

Community ENTASYS 200, Руководство по установке и эксплуатации, Страница: 12 / 28

Поделиться
Скачать
Community ENTASYS 200 Скачать руководство пользователя страница 12

ENTASYS 200 Installation/Operation Manual — Page 12  

 

ELECTRICAL INSTALLATION AND SAFETY

 

Electrical Safety 

DANGER: The output power capabilities of audio amplifiers present a danger to installers especially in 
70-volt and 100-volt distributed systems. To minimize the risk of electric shock from loudspeaker 
connecting cables, confirm that the power amplifiers are turned “off” before connecting loudspeaker 
cable(s) to the loudspeaker or amplifier. Always follow local electrical codes and proper electrical 
safety procedures. 

Electrical Connections and Cabling 

Input signal cabling for ENTASYS 200 Series loudspeakers can be connected to either the NL4-type 
connector, or to the input terminal strip on the bottom of the loudspeaker. A weather-resistant cover 
(included) can be attached to protect the input terminal connectors from moisture and debris. When 
the cover is in place, the NL4 connector cannot be used, and the range of vertical motion when wall-
mounted with the accompanying bracket mounting kit may be limited slightly.  

Cables, conduit, or liquid-tight couplings can be accommodated via the knock-out in the cover. A 1/2- 
inch NPT conduit knock-out is provided to accommodate conduit, gland nuts, strain relief fittings, etc.  

 

Outdoor Installations—Minimum Downward Installation Angle

 

NOTE: Whenever ENTASYS 200 loudspeakers are installed outdoors, or exposed to direct rain, other 
precipitation, or cleaning water, the loudspeaker enclosure must be angled downward at a minimum of 
2º (two-degrees) to meet the specified IP Rating and minimize water entry. 

 

 

MECHANICAL INSTALLATION AND SAFETY

 

Rigging and Safety Provisions 

All ENTASYS 200 models are designed to be mounted using only the included or optional 
ENTASYS rigging hardware. An appropriately sized Pan-Tilt wall bracket is provided with each 
ENTASYS 200 model. Bracket ships attached to the loudspeaker, loosely assembled.  

 

To suspend an ENTASYS 200 loudspeaker the Pan-Tilt Bracket should first be removed from the 
loudspeaker. Next the Pan/Tilt Bracket should be attached to the wall surface and adjusted to the 
desired estimated aiming angle. 

This is important, as it is easier and quicker to adjust the Pan-

Tilt Bracket before the loudspeaker has been installed. 

Detailed instructions are provided on 

Pages 14 through 18.

 

Lastly, install the ENTASYS 200 loudspeaker in the Pan-Tilt Bracket. Pilot holes are provided in 
several locations for fastening the loudspeaker to the Pan-Tilt Bracket, but it is also possible to 
attach the loudspeaker in other locations along the length of the extrusion, in order to derive the 
desired placement and vertical range of motion. Care should be given to ensure the Pan-Tilt bracket 
is placed as high on the cabinet that the focus angle will allow but not higher than necessary to 
ensure a secure and stable installation. Ensure that all four included 3.5x16mm Phillips Truss 
Head Screws are used when securing the Pan-Tilt Bracket to the cabinet. Once the ENTASYS 200 
loudspeaker is installed in the Pan-Tilt Bracket and the focus angle is adjusted, fully tighten each of 
the 3.5x16mm Phillips Truss Head Screws to fully secure the loudspeaker to the Pan-Tilt Bracket.  

 

Installation 

Содержание ENTASYS 200





























Отзывы:

Нет отзывов