manualshive.com logo in svg

CommScope Node AM4, Руководство пользователя

Поделиться
Скачать
CommScope Node AM4 Скачать руководство пользователя страница 80

 

8. Spare Parts List

 

Page 80 

   

MF0121ACP

_uc.docx

                      Manual for Node AM4 

 

 

Designation

 

ID No

 

Node AM4

 

7613589

 

DCM 
Com-
mercial 
Applica-
tions 
(US) 

DCM AF 727 (698 to 716 & 776 to 787 / 728 to 757 MHz) 

7577532-01

DCM AF 737 (698 to 716 & 776 to 787 / 728 to 757 MHz) 

7598983-01

DCM AF 8527 (824 - 849 / 869 - 894 MHz)

7577540-01

DCM AF 8537 (824 - 849 / 869 - 894 MHz)

7577542-01

DCM AF 1727 (1710 - 1755 / 2110 - 2155 MHz)

7577548-01

DCM AF 1727E (

1710 to 1780 / 2110 to 2180 MHz

)

7817693-00

DCM AF 1737 (1710 - 1755 / 2110 - 2155 MHz)

7577550-01

DCM AF 1927 (1850 - 1915 / 1930 - 1995 MHz)

7577552-01

DCM AF 1937 (1850 - 1915 / 1930 - 1995 MHz)

7577554-01

DCM AF 9037 (UL 896 - 902 MHz / DL 935 - 941 MHz)

7577546-01

DCM AF 8524 (AUS)

7801322-00

Dummy card 

7574285-00 

Dummy card T5 

7643315-00 

Fan Unit Backside Type (Kit) 

7574286 

Fain Unit Bottom  

7644217-00 

GPS Bias-T cable (AC/DC Cable USB 0.4 M Molex. 3 pol) 

7626927-00 

Modem-Kit PHS8 Node AM 

3)

 

7679538 

Modem-Kit PLS-8 Node AM EU 

7724196-00 

Power Supply Unit DC IN 24-110 V 680 W 

7609268-00 

Power Supply Unit DC IN 24-110V 780W

7711908-xx

Power Supply Unit AC IN 100-240 V 680 W 

7605769-00 

Rechargeable battery pack 6 V 

7613775-00 

Slot Duplexer passive (876-915/921-960 MHz) 

7621867-00 

User Interface 2 - Kit > V2.0.6 

4)

 7814162 

User's Manuals for Node AM4 

7617868-00 

VSWR Kit 925-960 MHz 

7622883 

VSWR-Module 925-960 MHz 

7614218-00 

3)

 

Modem-Kit PHS8 is the successor of Modem-Kit HC25 which has been discontinued 

4)

  Due to a PCB update on the UI2 Board (see also chapter 

4.3.6

), SW version V2.0.6 is mandatory for 

this kit (containing UI2 Board 7613646-05). The former User Interface 2 – Kit 7622884 (containing UI2 
Board 7613646-03) is no longer available. The UI2 Board cannot be ordered separately 

The manufacturer reserves the right to replace the parts listed above by equivalent 

substitutes. 

 

Note: 

To ensure compatibility with your system, do not order any individual 
components (e.g. modems) of the kits available. Make sure to always order 
the complete kit (ID must be listed above) as spare part. 

 
 

Содержание Node AM4




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды