manualshive.com logo in svg

CommScope Node AM4, Руководство пользователя

Поделиться
Скачать
CommScope Node AM4 Скачать руководство пользователя страница 19

3. Installation 

 

MF0121ACP

_uc.docx   

      

 Manual for Node AM4 

Page 19

 

3. Installation 

3.1. Mechanical  Installation 

3.1.1. Health 

and 

Safety for Mechanical Installation 

Read and observe chapter 

1.2

.  

1. Caution: 

Risk of injury by the considerable weight of the unit falling. Ensure there is 

adequate manpower to handle the weight of the system.

 

2. 

 

Caution: 

Risk of serious personal injury by equipment falling due to improper 

installation. The installer must verify that the supporting surface will safely support the 
combined load of the electronic equipment and all attached hardware and 
components. Only use sufficiently dimensioned screws for mounting and make sure 
the mounting material is adequate for the mounting surface.

 

3.1.2.  Property Damage Warnings for Mechanical Installation 

1. Attention: 

Do not install the unit in a way or at a place where the specifications 

outlined in the Environmental and Safety Specifications leaflet of the supplier are not 
met. 

 

2. Notice: 

 

Due to power dissipation, the unit may reach a very high temperature. 

Ensure sufficient airflow for ventilation. When mounting the Node AM4 into a train, a 
temperature test in maximum configuration (i.e. 4 RF cards) must essentially be 
made. A minimum air flow of 50 m³/h is required where the maximum air flow of the 
Node AM4 is 220 m³/h which will be reached at an environmental temperature of 
around 45°C and above. We suggest to supply the repeater at the air inlet with fresh 
air and to conduct warm air at the air outlet off the Node AM4 without feedback in 
order to avoid a 'thermal short-circuit'.

 

3. Notice: 

It is recommended only to use the mounting hardware delivered by the 

manufacturer. If any different or additional mounting material is used, ensure that the 
mounting remains as safe as the mounting designed by the manufacturer. Ensure 
that the static and dynamic strengths are adequate for the environmental conditions 
of the site. The mounting itself must not vibrate, swing or move in any way that might 
cause damage to the unit. The specifications for stationary use of the unit must not 
be exceeded.

 

 

Note:  Exceeding the specified load limits may cause the loss of warranty. 

4. Notice: 

Only use sufficiently dimensioned screws for mounting and make sure the 

mounting material is adequate for the mounting surface.

 

5. Notice: 

Observe that for M12 connectors the nominal torque is 1.0 N-m.

 

6. Notice: 

When connecting and mounting the cables (RF, mains, ...) ensure no water 

can penetrate into the unit through these cables.

 

7. Notice: 

Do not operate the repeater without terminating the antenna connectors. The 

antenna connectors may be terminated by connecting them to their respective 
antennas or to a dummy load.

 

Unless otherwise agreed to in writing by CommScope, CommScope’s general limited 
product warranty (

http://www.commscope.com/Resources/Warranties/

) shall be the 

warranty governing the Node AMs, including the installation, maintenance, usage and 
operation of the Node AMs. 

Содержание Node AM4




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды