manualshive.com logo in svg

CommScope ION-U EU H 23/23, Руководство пользователя

Поделиться
Скачать
CommScope ION-U EU H 23/23 Скачать руководство пользователя страница 7

1. General 

 

 

M0200ABA_ION-U_EU_H

_23_23

  User’s Manual for ION

®

-U 

Page 7 

 

1.2. Health and Safety 

 

1.  Danger

: 

Electrical hazard. Danger of death or fatal injury from electrical 

current. Obey all general and regional installation and safety regulations 
relating to work on high voltage installations, as well as regulations 
covering correct use of tools and personal protective equipment.

 

2.  Caution:

 High frequency radiation in operation. Risk of health hazards associated 

with radiation from the unit’s inner conductor of the antenna port(s). Disconnect 
mains before connecting or replacing antenna cables. 

3.  Caution:

 High frequency radiation in operation. Risk of health hazards associated 

with radiation from the antenna(s) connected to the unit. Implement prevention 
measures to avoid the possibility of close proximity to the antenna(s) while in 
operation. 

 

1.3. Property Damage Warnings 

 

1.  Attention: 

Due to power dissipation, the Extension  Unit  may reach a very high 

temperature. Do not operate this equipment on or close to flammable materials. 
Use caution when servicing the unit. 

2.  Notice

: Although the Extension Unit is internally protected against overvoltage, it 

is strongly recommended to ground  (earth) the antenna cables close to the 
repeater’s antenna connectors for protection against atmospheric discharge. 

3.  Notice

:  ESD precautions must be observed. Before commencing maintenance 

work, use the available grounding (earthing) system to connect ESD  protection 
measures. 

4. 

Notice:

 Only suitably qualified personnel are allowed to work on this unit and only 

after becoming familiar with all safety notices, installation, operation and 
maintenance procedures contained in this manual.

 

5.  Notice:

  Keep operating instructions within easy reach and make them available 

to all users. 

6.  Attention:

  Only authorized and trained personnel are allowed to open the unit 

and get access to the inside. 

7.  Notice:

 Read and obey all the warning labels attached to the unit. Make sure that 

all warning labels are kept in a legible condition. Replace any missing or 
damaged labels. 

 

 

Содержание ION-U EU H 23/23


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды