manualshive.com logo in svg

CommScope ION-U EU H 23/23, Руководство пользователя

Поделиться
Скачать
CommScope ION-U EU H 23/23 Скачать руководство пользователя страница 26

 

4. Commissioning 

 

Page 26 

M0200ABA_ION-U_EU_H_23_23 

  User’s Manual for ION

®

-U 

 

ION-U High Power RU Connectors/Indicators 

 

Port/Conn 

Purpose 

Type 

 

ANT MAIN  

This connector is used for transmitting and 
receiving either the combined signals from RU 
and EU or SISO or MIMO 2300 MHz path 1. 

4.3-10 type 

female 

 

7-21 IN-

MIMO 

This connector is used for combining the signals 
from the second EU and the MIMO 2300 MHz 
path 2. If not used, the termination on the port 
must not be removed. 

4.3-10 type 

female 

 

EXPANSION 

This connector is used to interconnect to the 
Remote Unit to provide additional bands of 
coverage. 

Radiall Opus 

M424400-

003 

 

PROBE 

MAIN 

This connector is used as measurement probe to 
antenna port ANT-MAIN. 

QMA 

 

PROBE 

MIMO 

This connector is used as measurement probe to 
antenna port ANT-MIMO. 

QMA 

 

STATUS 

This LED provides a visual warning of an alarm 
condition. The color of the LED indicates the 
severity of the alarm.

 

LED 

 

MAINS  

This connector provides power to EU models that 
use standard AC (100 to 240 Vac) power. 

Coninvers 

M17 –Series 

P20, 4-Pin 

 

EXPANSION 

EU 

This connector is used to interconnect to the 
second Extension Unit to provide additional 
bands of coverage. 

Radiall Opus 

M424400-

003 

 

7-21 IN-

MAIN 

This connector is used for combining the signals 
from the RU and the MIMO 2300 MHz path 1. If 
not used, the termination on the port must not be 
removed. 

4.3-10 type 

female 

 

ANT MIMO  

This connector is used for transmitting and 
receiving either the combined signals from EU 
and EU or SISO or MIMO 2300 MHz path 2. 

4.3-10 type 

female 

 

Grounding 

Bolts 

Ground (earth) bolts for connecting the 
mandatory ground cable to the EU 

M6 bolts, 

hex nut, & 

washers 

table 4-2 ION-U EU H 23/23 connector flange 

 

 

K 

J 

I 

H 

G 

F 

E 

D 

C 

B 

A 

Содержание ION-U EU H 23/23


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды