background image

ADCP-90-516 • Rev B • April 2019

Page 19

© 2019, CommScope, Inc.

5.4

Using the Horizontal Management Panel

To store a length of cable in the storage deck panel, perform the following procedure:

1. Store the first cable on the rear spools, making sure that the final turn comes off the inner

part of the rear spool as shown in 

Figure 15

. Then route the cable to the left rear corner of

the panel.

2. Next, route cable toward the front left front of the management panel and out into the

vertical cable guide; adjust cable slack as necessary to ensure that no pinching or binding
occurs.

3. Store the second cable on the pair of spools at the front of the storage panel; when it exits

the spools, route it through the cable guide at the back of the panel.

4. Complete a designation label for the stored patch cord and apply label to front edge of

management panel assembly.

5. Repeat procedure for each patch cord to be stored. 

Figure 15. Horizontal Management Panel Cable Storage

Caution: 

Do not kink or make a sharp bend in the patch cord when forming loop. Excessive

bending may damage the optical fiber within the patch cord

.

18878-A

Содержание FL2000 Storage Panel





















Отзывы: