background image

ODPMT200 Series DryLine® Dehydrator User Manual

11

every 6000 hours of compressor operation.  The 

kit listed below, contains all of the necessary 

parts to perform this overhaul.

Maintenance Parts

1.  Dehydrator Overhaul Kit 1 ea. 

AE01K-C0398-015

2.  Compressor Air Intake Filter bag of 6, 

EFLTR-91101

Tools

The following tools are used in the maintenance 

and overhaul procedures. 

A ballpoint pen, an adjustable open-end wrench, 

a socket wrench with a 7/16-inch (or 11mm) 

socket, a No. 2 Phillips screwdriver and a small 

flat-blade screwdriver.

Overhaul Procedure

When the ODPMT200 compressor run time 

reaches 6000 hours (or a multiple of 6000 

hours) it is time to replace certain items in the 

compressor and the air path of the dehydrator.  

These include the piston cups, piston seals 

and head gaskets of the compressor, the filter 

elements in the water and coalescing filters and 

the tube section connecting the compressor 

output to the water filter input.

Unit Shutdown and Removal

In order to perform an overhaul on the 

ODPMT200, the unit must be turned off and 

removed from service.  As this is being done 

the low pressure alarm may activate through a 

reporting alarm system.  Personnel monitoring 

such an alarm should be notified in advance 

so that they are aware of the fact that service 

is being performed.  It is also necessary to 

disconnect the dehydrator dry air output from the 

waveguide system during the overhaul.

3.7 

Dehydrator Filter Element  Replacement

Clean/replace the air intake filter

The air intake filter protects the compressor 

from contamination and dust.  Periodic cleaning/

replacement extends the life of the compressor. 

The filter is made of open-cell foam material.  It 

should be cleaned or replaced once a year (or 

more frequently, if the operating environment is 

very dusty.)

Pull off the filter cover and remove the foam 

element.  (The cover is held in place by two 

tabs.  Use a small screwdriver or a ballpoint pen 

to release them.)

Wash the filter in running water, squeezing it 

between the fingers.

Содержание DryLine ODPMT200 Series





















Отзывы: