manualshive.com logo in svg

CommScope 360G2-iP-1U-32-MPO-DP-SD, Инструкция

Поделиться
Скачать
CommScope 360G2-iP-1U-32-MPO-DP-SD Скачать руководство пользователя страница 4

860538982 
Instruction Sheet 

 

www.commscope.com 

 

Page 4 of 9 

 

Step 1 

– Route Panel Bus Jumper 

 
 

1.  If it has not already been removed, slide the cover off the shelf. 

2.  Remove tape securing panel bus jumper to cable support. 

3.  Route the panel bus jumper with protective corrugated tubing around the end of the sliding rail to the outside 

of the rail. 

4.  Snap the corrugated tubing protecting panel bus jumper into the cable retainer clip on the outside of rail as 

shown. 

5.  Position the corrugated tubing so that about 3.5 inches (89mm) of tubing extends past the end of cable 

retainer clip. 

6.  Position  the  exposed  ribbon  cable  of  the  panel  bus  jumper  in  the  flat  retainer  clips  on  the  outside  of  the 

sliding rail as shown above.

 

 

 

 

10-pin panel
bus jumper
connector

Panel 
jumper

bus

Protective
corrugated tubing

Flat retainer clips 

3.5”

(89mm)

.....

.....

Содержание 360G2-iP-1U-32-MPO-DP-SD










Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды