Command Light CL602A Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 48

Command Light CL602A Скачать руководство пользователя страница 14

COMMAND LIGHT

13

Electrical Wiring

Please Note:

Detailed internal wiring schematic for the light is found in the supplement pages found at

the end of this document.

Run the control wire from the control box holster to the

COMMAND LIGHT

.

Run the power wire from the breaker box or generator to the

COMMAND LIGHT

. A 40 Amp breaker

is recommended on AC models.

Make the control connections in the

COMMAND LIGHT

entrance box. To simplify installation remove

the connector hold down screws and pull the connector out of the box slightly.

The Model CL602A series

COMMAND LIGHT

comes pre-wired to connect to 120 VAC.

Holster Wiring

Determine if an elevated warning device will be used in conjunction with the light tower. If a warning

device will be used, use the wiring diagram on the next page, otherwise, use the wiring diagram in the

back of the user guide.

After routing the control cable into the holster through the sealing connector, attach individual wires to

the provided connectors and insert the connectors into the proper ports on the circuit board.

120 VAC Wiring Diagram

240 VAC Wiring Diagram

If 240 VAC operation is desired, remove the

jumper wire between the red and black leads.

220 VAC European Wiring Diagram

If the light tower is ordered with 220 VAC (Single

Hot Leg) wiring, only use a single hot conductor

from the power source, the other is not needed.

«
...
12
13
14
15
16
...
»

Содержание CL602A

















































Отзывы:

Нет отзывов