manualshive.com logo in svg

Command Communications ASAP 104, Инструкция по установке и справочник

Поделиться
Скачать
Command Communications ASAP 104 Скачать руководство пользователя страница 37

 

 

37

 

═════════════════════════════════════════════════════════════════

 

DRS Assignment 

 

The DRS Assignment operates in either the Automatic mode or the Semi-Automatic mode. 
 
This feature designates where the ASAP 104 will transfer a call using the Distinctive Ring service. It has the ability to 
recognize four different ring signals:  
 

0- - - no ring assigned 
1- - - standard ring 
2- - - two-burst ring 
3- - - three-burst ring (short-short-long) 
(Short short short) 
(Long long long) 
(Long short short) 
(Short long long) 
4- - - three-burst ring (short-long-short) 
(Long short long) 
(Long long short) 

 
 
The ASAP 104 looks for a 4-digit entry to set the port designations for the individual rings.  The first digit represents portP1, 
the second digit represents port P2, the third digit represents port P3, and the fourth digit represents port P4. The ASAP 104 
cannot be set to transfer any ring signal to more than one port. 
 
The factory setting is 

# * (three beeps) 8 0 1 2 3 4 * 

which transfers a standard ring to port P1, a two burst ring to port P2, a 

three burst ring (above) to port P3, and a three burst ring (above) to port P4. 
 
To change this feature, perform the following steps: 
 

1. Take the phone in port P1 off-hook 
2. Press

 # * (three beeps) 8 0 _ _ _ _ * (three beeps) * (one beep)  

(blank spaces represent the new DRS 

Assignment) 
3. Hang up the phone 

 
NOTE: If a ring burst is not assigned, the ASAP 104 will not respond to the incoming call designated to that phone number.  
 
Each ring burst can be assigned to 1 port. If you attempt to assign a ring burst to more than 1 port, the ASAP 104 will give 
an error tone. 

 

═════════════════════════════════════════════════════════════════

 

Reset to Factory Settings

 

 

To reset all features and feature settings to their original factory settings, perform the following steps: 
 

1. Take the phone in port P1 off-hook 
2. Press 

# * (three beeps) 9 9 9 *  (three beeps) * (one beep)  

3. Hang up the phone 
 

 

Содержание ASAP 104









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды