Command Communications ASAP 104 страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 40

background image

19

Programming the ASAP 104

═════════════════════════════════════════════════════════════════

Introduction

The ASAP 104 has many features that can be used to customize its operation.

Many of these features have either feature settings or timing parameters associated directly with their operation.
Therefore, read the following sections carefully to obtain the best results when programming the ASAP 104.

═════════════════════════════════════════════════════════════════

Programming Locally

Connect the ASAP 104 as shown, using a tone phone.

Programming changes can be performed from a tone phone connected to port P1 of an operational unit.

To enter the programming mode, take the phone off-hook, press

# *

. You will hear three beeps indicating the unit

is in the programming mode

Once in programming, the ASAP 104 allows 8 seconds between tone commands before exiting the programming
mode without saving the changes. Therefore, it would be beneficial to write down all programming changes before
entering the programming mode.

Once a complete programming command is entered, it must be followed by the

*

key, which stores it into memory.

After you enter the

*

key, you can set as many features or feature settings as needed for your application. When all

programming changes are complete, press

* *

to save the changes to exit the programming mode. There is one

final beep when exiting programming mode before returning to a dial tone.

The ASAP 104 will not be able to process calls during programming sessions.

If during a programming session you receive a dial tone, the intercept operator message, or if programming was not
successful, perform the following steps:

1

.Disconnect the telephone line from the TEL LINE port.

2

.Take the phone in port P1 off-hook.

3

.Disconnect power from the ASAP 104.

4

.Reconnect power to the ASAP 104.

5

.The ASAP 104 will produce three beeps indicating entry into the programming mode.

6

.Continue with programming changes as previously described.

7

.When programming changes are complete, hang up the phone.

8

.Reconnect the telephone line.

NOTE: Programming changes can only
be made through port P1 even if the
Primary port is reassigned.

«
...
17
18
19
20
21
...
»

Содержание ASAP 104









































Отзывы:

Нет отзывов

Похожие инструкции для ASAP 104

OFFICESERV 100 Series

Бренд: Samsung Страницы: 42

Бренд: Echo Страницы: 4

Бренд: WÄRTSILÄ Страницы: 64

Бренд: Patton electronics Страницы: 12

Бренд: Q'STRAINT Страницы: 10

Бренд: T-Comfort Страницы: 48

Бренд: Talkswitch Страницы: 3

IO-Link BAE SA-CS-027-YI-BP00,3 GS04

Бренд: Balluff Страницы: 50

Бренд: Montech Страницы: 17

Бренд: Shenzhen Страницы: 13

Бренд: Heitronic Страницы: 4

Бренд: Phonocar Страницы: 2

SafeAir M-600 Pro

Бренд: ParaZero Страницы: 23

Бренд: Spiral Audio Страницы: 2

Бренд: FALCON RIDGE Страницы: 8

Бренд: Dennis Kirk Страницы: 5

Бренд: Scosche Страницы: 8

Бренд: hepco & becker Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды