Comfort Glow GSD2211 Скачать руководство пользователя страница 15

15

INSTALLATION

CONNECTING TO GAS SUPPLY

 WARNING

: A qualified service technician must connect heater to gas supply. Follow all local  

codes. 

 CAUTION:

 Never connect heater directly to the gas supply. This heater requires an external

regulator (not supplied). The external regulator between the gas supply and heater must be installed. 
Gas supplier provides external regulator for natural gas. 

 WARNING

: Never connect heater to private (non-utility) gas wells. This gas is commonly known  

as wellhead gas.
The installer must supply an external regulator for liquid propane. The external regulator is
provided by the gas supplier for natural gas. The external regulator will reduce incoming gas pres-
sure. You must reduce incoming gas pressure to between 11 and 14 in. of water column for propane 
and between 6 and 14 in. of water column for natural gas. If you do not reduce incoming gas pres-
sure, heater regulator damage could occur. Install external regulator with the vent pointing down as 
shown in Fig. 9. Pointing the vent down protects it from freezing rain or sleet.

* Purchase the optional equipment shutoff valve from your local Home Center store.

 CAUTION

: Use only new black iron or steel pipe. Internally tinned copper tubing

 

may be used in certain areas. Check your local codes. Use pipe of ½ in. diameter

 

or greater to allow proper volume gas to heater. If pipe is too small, loss of pressure

 

will occur. Installation must include an equipment shutoff valve, union, and plugged

 

1/8-in. NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must

 

be upstream from heater (See Fig. 10).

IMPORTANT

: Install equipment shutoff valve in an accessible location. The equipment

shutoff valve is for turning on or shutting off the gas to the appliance. Apply pipe joint
sealant lightly to male threads. This will prevent excess sealant from going into pipe.
Excess sealant in pipe could result in clogged heater valves.

Approved

Flexible

Gas Line

or 1/2''

Black Pipe

Fig. 9 - Regulator Conversion

Fig. 10 - Gas Connection

(11"

(6"

14"

14"

Содержание GSD2211




























Отзывы: