background image

IE-LOG-S5141-01 

 

  9 

Battery replacement 

Low  battery  is  indicated  on  the  display  by  blinking  of  reading  "BAT".  It  can  be  displayed 

permanently, if battery voltage is too low. Replace the battery for new one. Applied is Lithium battery 
3,6 V, size AA. Battery is located under logger lid. 

Warning:

  near  battery  fragile  glass  reed  contact  is  located  –  be  careful  not  to  damage  it.  Be 

careful in battery replacement! 

 

Replacement procedure: 

 

switch off the logger by the PC program or by magnet (if low battery allows) 

 

unscrew four corner screws and remove the lid 

 

remove old battery by pulling the glued tape 

 

insert new battery 

respecting the correct polarity

 (see s and – near battery holder). If 

you connect  new battery up to  30 s, all logger settings remain unchanged.  In the opposite case 
check by means of PC program all settings, especially the real time clock in logger. 

Attention, 

inserted battery with incorrect polarity causes logger damage!

 

 

put the lid back again and screw four screws. Be careful to have the rubber sealing properly in the 
slot and tighten the screws properly to ensure the water resistance of the instrument. 

 

connect logger to the computer and 

write to it the information on battery replacement

. This 

step is necessary to evaluate properly the remaining battery capacity. 

 

Old battery or logger itself (after its life) is necessary to liquidate ecologically! 
 
 

 

 

Instrument passed through tests of electromagnetic compatibility (EMC): 

 

Device conforms in accordance with EN 61326-1 these norms: 

 

radiation:  

EN 55011 Class B 

 

immunity:  

EN 61000-4-2 (levels 4/8 kV, Class A) 

 

 

 

EN 61000-4-3 (intensity of electric field 3 V/m, Class A) 

 

 

 

EN 61000-4-4 (levels 1/0.5 kV, Class A) 

 

 

 

EN 61000-4-6 (intensity of electric field 3 V/m, Class A) 

 
 
 

Technical support and service 

Technical support and service is provided by distributor. Contact is included in warranty 

certificate. 
 

Содержание S5141










Отзывы: