Comdronic AC7 Скачать руководство пользователя страница 16

Страница: 16 / 22

www.comdronic.co.uk

Default = 5 min

The Auto-Off Timer sets the period of time after which the

AC7

will turn ‘OFF’ after a period of inactivity.

A short time will preserve battery life.

Fig. 20

Default = mm

This menu option allows the user to specify the preferred units for viewing and selecting valve sizes.

Fig. 21

This is the internal pipe diameter of the pipework that the target measuring valve / device is installed in and it
is used by the

AC7

to establish the velocity in the pipe for flushing purposes. Velocity units are available (m/s

or f/s) and these can be selected in the Units Menu. A valve will need to be selected (see page 8) in order for
this feature to be used.

Fig. 22

Once the new value is correct on the screen, press

to accept it. Or, press

EXIT

to exit the screen and retain

the current setting.

Select Auto-Off Time

5 min

Use the

▲▼

buttons to move
between the
settings.
Press

to accept.

10 min

1 min

Always On

View Size As

Use the

▲▼

buttons to move
between the
settings.
Press

to accept.

Inches

= 16.1 mm

Use the

►

button

to add a digit.

Current setting.

Internal Pipe Diameter

Use the

◄

button

to remove a digit.

Use the

▲▼

buttons

to increase or
decrease a value.

Содержание AC7























Результаты поиска

Содержание AC7

Отзывы:

Comdronic AC7, Руководство по эксплуатации, Страница: 16 / 22

Результаты поиска

Содержание AC7

Отзывы: