Comdial Conversip EPI00G-I12 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 140

Comdial Conversip EPI00G-I12 Скачать руководство пользователя страница 63

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

63

4.6.1 SCREENED TRANSFERS

You can answer a call at your endpoint and transfer it to another
station. If you first identify the caller to the party receiving the
transfer (giving that user the opportunity to prepare for the call), you
have made a screened transfer.

To screen and transfer a call to another
endpoint in the system, perform the
following steps.

1. Answer the call.
2. Press the

TRNS/CONF

button or

select

Transfer

(call is automati-

cally placed on hold).

3. Dial the extension number of the

endpoint you want to receive the
transfer, or press a DSS/BLF
button for that extension.

4. Announce the call when intercom party answers.
5. Press

SPEAKER

to disconnect (if in speakerphone mode), or

hang up.

The intercom party then has the call (if they answered the screened
transfer with the handset). If you announce the transfer over the
speaker, the intercom party’s telephone rings with the transferred call
after you hang up.

If the intercom party is busy, take one
of the following steps (if made
available at your endpoint by installer
programming).

• Select

Reconnect

to reconnect the

call to your station.

• Select

Message

to leave a

message-waiting indication at the
called station.

«
...
61
62
63
64
65
...
»

Содержание Conversip EPI00G-I12













































































































































Отзывы:

Нет отзывов